Seguridad General - Genie GR-12 Manual Del Operario

Cuarta edición • Segunda impresión
Señales de seguridad y ubicaciones
Pegatinas que contienen texto
44736
N° de pieza 133069SP
Failure to read, understand and obey the operator's manual and the following safety rules will
result in death or serious injury.
Improper Use Hazard Tip-over Hazards
The operator is responsible for safe machine operation.
This includes:
1 Avoid hazardous situations.
2 Always perform a pre-operation inspection.
3 Always perform function tests prior to use.
4 Inspect the work place.
5 Only use the machine as it was intended.
Do not operate unless:
You read, understand and obey:
- manufacturer's instructions and safety rules—
safety and operator's manuals and decals
- employer's safety rules
- applicable governmental regulations
You are properly trained to safely operate this machine.
Use extreme care and slow speeds while driving the machine
Electrocution Hazards
in stowed position across uneven terrain, debris, unstable or
This machine is not electrically
slippery surfaces and near holes and drop-offs.
insulated and will not provide
Do not place or attach overhanging loads to any part of this
protection from contact with or
machine.
proximity to electrical current.
Do not push off or pull toward any
Maintain safe distances from
object outside of the platform.
electrical power lines and apparatus in
accordance with applicable
Do not alter or disable machine
governmental regulations and the
components that in any way affect
following chart.
safety and stability.
Maintain required clearance. Do not place ladders or scaffolds in
Line voltage Required clearance platform or against any part of this
300V to 50KV 10 ft 3.05 m machine.
50KV to 200KV 15 ft 4.60 m
Do not drive machine on a slope that
200KV to 350KV 20 ft 6.10 m
exceeds the maximum slope or slide
350KV to 500KV 25 ft 7.62 m
slope rating of the machine.
500KV to 750KV 35 ft 10.67 m
Do not use machine on a moving or
750KV to 1000KV 45 ft 13.72 m
mobile surface or vehicle.
Be sure all tires are in good condition,
Explosion Hazards
castle nuts are properly tightened and
Do not operate machine or charge battery in hazardous
cotter pins are properly installed.
locations or locations where potentially flammable or
Do not depend on tilt alarm as a level indicator. Tilt alarm
explosive gases or particles may be present.
sounds only when the machine is on a slope.
If tilt alarm sounds, lower the platform. Move machine to a
firm, level surface. Use extreme caution to lower platform.
Do not alter or disable limit switches.
133014 A
31508
DANGER
Electrocution / Fire Hazard
Death or serious injury will
result from use of improper or
damaged cord and outlet.
Connect charger to a grounded
AC 3-wire electrical outlet only.
Before each use, inspect for
damaged cord, cables and
wires. Replace damaged items
before operating.
31508 C
GR-12 • GR-15 • GR-20

Seguridad general

DANGER
Crushing Hazards
Do not exceed rated load capacity. Use common sense and planning when operating machine with
controller from ground. Maintain safe distances between
Maximum occupancy: 1 person.
operator, machine and fixed objects.
Do not raise platform when wind
Fall Hazards
speeds may exceed 28 mph / 12.5 m/s.
The guard rail system provides fall protection. If occupants of
Do not operate machine in strong or
the platform are required to wear personal fall protection
gusty winds. Do not increase surface
equipment (PFPE) due to job site or employer rules, PFPE
area of platform or load. Increasing
equipment and its use shall be in accordance with the PFPE
area exposed to wind will decrease
manufacturer's instructions and applicable governmental
machine stability.
requirements.
Do not drive machine on or near
uneven terrain, unstable surfaces or
other hazardous conditions with the
platform raised.
Keep platform floor clear of debris.
Collision Hazards
Be aware of extended platform position when moving machine.
No stunt driving or horseplay while operating a machine.
Damaged Machine Hazards
Do not use a damaged or malfunctioning machine.
Be sure all maintenance has been performed as specified in the
appropriate operator's and service manuals.
Be sure all decals are in place and legible.
Be sure operator's, safety and responsibilities manuals are
complete, legible and in the storage container located on the
platform.
Manual del operario
133014
Do not sit, stand or climb on the platform
guard rails. Maintain a firm footing on the
platform floor at all times.
Do not climb down from the platform
when raised.
Lower platform mid-rail bar or close
platform gate before operating.
Be aware of limited sight distance and
blind spots when driving or operating.
Check work area for overhead
obstructions or other possible hazards.
Be aware of crushing hazard when
grasping platform guard rail.
Do not lower platform unless area below
is clear of personnel and obstructions.
5