Evolution R185 SMS Instrucciones Originales página 8

d) Push the saw through the workpiece.
Do not pull the saw through the workpiece. To
make a cut, raise the saw head and pull it out
over the workpiece without cutting, start the
motor, press the saw head down and push the
saw through the workpiece. Cutting on the pull
stroke is likely to cause the saw blade to climb on
top of the workpiece and violently throw the blade
assembly towards the operator.
NOTE: The above warning is omitted for a simple
pivoting arm mitre saw.
e) Never cross your hand over the intended
line of cutting either in front or behind the saw
blade. Supporting the workpiece "cross handed" i.e.
holding the workpiece to the right of the saw blade
with your left hand or vice versa is very dangerous.
f) Do not reach behind the fence with either
hand closer than 150mm from either side of the
saw blade, to remove wood scraps, or for any
other reason while the blade is spinning. The
proximity of the spinning saw blade to your hand
may not be obvious and you may be seriously
injured.
g) Inspect your workpiece before cutting. If
the workpiece is bowed or warped, clamp it
with the outside bowed face toward the fence.
Always make certain that there is no gap
between the workpiece, fence and table along
the line of the cut. Bent or warped workpieces
can twist or shift and may cause binding on the
spinning saw blade while cutting. There should be
no nails or foreign objects in the workpiece.
h) Do not use the saw until the table is clear
of all tools, wood scraps, etc., except for the
workpiece. Small debris or loose pieces of wood
or other objects that contact the revolving blade
can be thrown with high speed.
i) Cut only one workpiece at a time. Stacked
multiple workpieces cannot be adequately
clamped or braced and may bind on the blade or
shift during cutting.
j) Ensure the mitre saw is mounted or placed on
a level, firm work surface before use. A level and
firm work surface reduces the risk of the mitre saw
becoming unstable.
k) Plan your work. Every time you change the
bevel or mitre angle setting, make sure the
adjustable fence is set correctly to support the
workpiece and will not interfere with the blade
or the guarding system. Without turning the tool
"ON" and with no workpiece on the table, move
www.evolutionpowertools.com
the saw blade through a complete simulated cut
to assure there will be no interference or danger of
cutting the fence.
NOTE: The phrase "bevel or" does not apply for
saws without bevel adjustment.
l) Provide adequate support such as table
extensions, saw horses, etc. for a workpiece
that is wider or longer than the table top.
Workpieces longer or wider than the mitre saw
table can tip if not securely supported. If the
cut-off piece or workpiece tips, it can lift the lower
guard or be thrown by the spinning blade.
m) Do not use another person as a substitute
for a table extension or as additional support.
Unstable support for the workpiece can cause the
blade to bind or the workpiece to shift during the
cutting operation pulling you and the helper into
the spinning blade.
n) The cut-off piece must not be jammed or
pressed by any means against the spinning
saw blade. If confined, i.e. using length stops, the
cut-off piece could get wedged against the blade
and thrown violently.
o) Always use a clamp or a fixture designed to
properly support round material such as rods
or tubing. Rods have a tendency to roll while
being cut, causing the blade to "bite" and pull the
work with your hand into the blade.
p) Let the blade reach full speed before
contacting the workpiece. This will reduce the
risk of the workpiece being thrown.
q) If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving parts
to stop and disconnect the plug from the power
source and/or remove the battery pack. Then
work to free the jammed material. Continued
sawing with a jammed workpiece could cause loss
of control or damage to the mitre saw.
r) After finishing the cut, release the switch,
hold the saw head down and wait for the blade
to stop before removing the cut-off piece.
Reaching with your hand near the coasting blade
is dangerous.
s) Hold the handle firmly when making an
incomplete cut or when releasing the switch
before the saw head is completely in the down
position. The braking action of the saw may cause
the saw head to be suddenly pulled downward,
causing a risk of injury.
NOTE: The above warning applies only for mitre
saws with a brake system.
8