Warranty Registration; Storage & Service - Tripp-Lite SmartPro Manual Del Usuario

Basic Operation
continued
distortion by experimenting with different settings for this dial. As the dial is
turned clockwise, the UPS becomes more tolerant of variations in its input
power's AC waveform. NOTE: The further the dial is adjusted clockwise, the
greater the degree of waveform distortion the UPS will allow to pass to connected
equipment. When experimenting with different settings for this dial, operate
connected equipment in a safe test mode so that the effect on the equipment of
any waveform distortions in the UPS's output can be evaluated without dis-
rupting critical operations.
Storage & Service
Storage
CAUTION! Your UPS has an internal power source. Its outlets may still deliver current, even after the UPS
is unplugged, until the UPS is completely turned OFF (deactivated). Before storing your UPS, turn it com-
pletely OFF: with the UPS ON and receiving utility power, press and hold the POWER button for one sec-
ond (an alarm will beep once briefly after the interval has passed); then, unplug the UPS from the wall out-
let. If you store your UPS for an extended period of time, recharge the UPS batteries once every three
months: plug the UPS into a wall outlet; allow it to charge for 4 to 6 hours; and then unplug it and place it
back in storage. Note: after you plug the UPS in, it will automatically begin charging its batteries; howev-
er, it will not supply power to its outlets (see Quick Installation section). If you leave your UPS batteries
discharged for an extended period of time, they will suffer a permanent loss of capacity.
Service
Before returning your UPS for service, follow these steps:
1. Review the installation and operation instructions in this manual to ensure that the service problem does
not originate from a misreading of the instructions. Also, check that the UPS System's circuit breaker(s) are
not tripped. This is the most common cause of service inquiries which can be easily remedied by follow-
ing the resetting instructions in this manual.
2. If the problem continues, do not contact or return the UPS to the dealer. Instead, call Tripp Lite at (773)
869-1233. A service technician will ask for the UPS's model number, serial number and purchase date and
will attempt to correct the problem over the phone.
3. If the problem requires service, the technician will issue you a Returned Material Authorization (RMA)
number, which is required for service. If you require packaging, the technician can arrange to send you
proper packaging. Securely pack the UPS to avoid damage during shipping. Do not use Styrofoam beads
for packaging. Any damages (direct, indirect, special, incidental or consequential) to the UPS incurred dur-
ing shipment to Tripp Lite or an authorized Tripp Lite service center is not covered under warranty. UPS
Systems shipped to Tripp Lite or an authorized Tripp Lite service center must have transportation charges
prepaid. Mark the RMA number on the outside of the package. If the UPS System is within the 2-year war-
ranty period, enclose a copy of your sales receipt. Return the UPS for service using an insured carrier to the
address given to you by the Tripp Lite service technician.
8

Warranty Registration

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product.
You'll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product! *
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
FCC CLASS A RADIO/TV INTERFERENCE NOTICE (U.S. ONLY):
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when operated in a commercial environment. This equip-
ment generates, uses and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause interference to radio communications.
Operation of this equipment is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense. The user must use shielded cables and
connectors with this product. Any changes or modifications to this product not expressly approved
by the party responsible for compliance could void the user's authority to operate the equipment.
FCC CLASS B RADIO/TV INTERFERENCE NOTICE (U.S. ONLY):
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with the
instruction manual, may cause interference to radio communications. However, there is no guar-
antee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference using one or more
of the following measures: reorient or relocate the receiving antenna; increase the separation
between the equipment and the receiver; connect the equipment into an outlet on a circuit differ-
ent from that which the receiver is connected; consult the dealer or an experienced radio/televi-
sion technician for help. The user must use shielded cables and connectors with this product. Any
changes or modifications to this product not expressly approved by the party responsible for com-
pliance could void the user's authority to operate the equipment.
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product
has been assigned a unique series number. The series number can be found on the product
nameplate label, along with all required approval markings and information. When requesting
compliance information for this product, always refer to the series number. The series number
should not be confused with the marking name or model number of the product.
Tripp Lite follows a policy of continuous improvement. Product specifications are subject to
change without notice.
Note on Labeling
Two symbols are used on the label.
V~ : AC Voltage
V : DC Voltage
9