Important Safety Instructions - HAMPTON BAY 724-491 Manual De Instrucciones

Thank you for purchasing this Hampton Bay interior rigid track kit. This product has been manufactured with the
highest standards of safety and quality.
FEATURES:
1. This linear track kit includes 1, 44in. track section, 1 floating canopy, 1 straight connector (for BK) and 3 Track
Heads.
2. Track heads are multi-directional to provide light in hard to reach places.
3. This track kit can be mounted to a wall or a ceiling.
4. The floating power feed was designed to supply power anywhere along the track system.
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer Service Team at 1-877-527-0313 or visit
www.homedepot.com. Please reference SKU 724-491, UPC 008938101325 or SKU 142-780, UPC 008938101318.
GENERAL:
1. Be sure to read these installation instructions and review the diagrams thoroughly before installing the track
system.
2. All electrical connections must be in accordance with local codes and the National Electrical Code. If you are
unfamiliar with methods of installing electrical wiring, secure the services of a qualified licensed electrician.
3. Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the
appropriate fuse at the fuse box. Turning the power off using the light switch is not sufficient to prevent electrical
shock.
Note: The important safeguards and instructions appearing in this manual are not meant to cover all possible
conditions and situations that may occur. It must be understood that common sense, caution and care are factors that
cannot be built into any product. These factors must be supplied by the person(s) caring for, installing and operating
the fixture. If at any time you are uncomfortable or are unsure of what to do, please contact a qualified licensed
electrician for further assistance.

IMPORTANT SAFETY INSTRUCTIONS

WHEN INSTALLING OR USING THIS TRACK SYSTEM, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED INCLUDING THE FOLLOWING:
1. Read all instructions. Save these instructions and refer to them when additions to or changes in the track
configuration are made.
2. Do not install this lighting system in a damp or wet location.
3. Before energizing make sure that the lighting system is clear of all material which could cause a direct short and
check all electrical connections to make sure they are secure.
4. Do not install any part of this system (TRACK) less than 7 feet (2.2m) above floor.
5. Do not install any lamps closer than 6 inches (15.25cm) from any curtain or similar combustible material.
6. For installation with EC series track only.
7. CAUTION – To reduce the risk of a burn during re-lamping, remove from the track before re-lamping.
8. This track system is not intended for the use with a power supply cord or convenience receptacle adaptor.
9. This track system is to be supplied by a single branch 120 volt circuit.
10. The track is not intended to be pendant mounted such as by a stem or cable.
11. The mounting screws are to be mounted along the track in the keyhole slots provided.
12. Disconnect electrical power before adding to or changing the configuration of the track.
13. Do not attempt to energize anything other than EC series track lighting fixtures or components on the track. To
reduce the risk of fire and electrical shock, do not attempt to connect power tools, extension cords, appliances, etc.
to the track.
14. CAUTION: Lighted lamp is hot! Do not touch lamp at any time. Use a soft cloth, Oil from skin may damage
lamp.
15. CAUTION – Hot surface, keep away from curtains and other combustible materials.
16. Lamp gets hot quickly! Contact only switch or plug when turning on. Do not touch hot lamp lens.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION (not included):
Ladder Safety goggles
Electrical tape Drill
PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
x1 Canopy x 2 Toggle
bolts
SAVE THESE INSTRUCTIONS
Wire stripper Gloves
1/4 In. (method 1) or 5/8 In. (method 2) Drill bits
x1 44in. x3 GU10
Linear Track Shielded Bulb
Flathead screwdriver
Box
x1 Hardware x3 Track
Packet Fixtures
2
Phillips screwdriver
1 straight
Connector