Microsoft Surface Hub 55 Manual De Usuario página 4

WARNING: Proper installation environment
To reduce risks related to the environment, the unit must be installed indoors only.
• It is the consumer's responsibility to ensure that structural engineering requirements for potential seismic activity are met per your local requirements. This may require wall reinforcement.
• Do not install near sources of high heat or steam or where condensation is likely to occur, such as near air conditioners.
• Do not install on a structure that is prone to vibration or movement.
• Do not install in such a way as to block ventilation holes. Allow for proper ventilation according to the device specifications.
• Do not install in areas with potentially explosive atmospheres. These areas are often, but not always, posted and can include fueling areas, such as below decks on boats, fuel or chemical transfer or storage facilities, or areas where the air
contains chemicals or particles, such as grain dust or metal powders. The device should not be used in these areas. In such areas, sparks can occur and cause an explosion or fire.
WARNING: Handling and site preparation
• Do not attempt to install the device with fewer than the required number of individuals.
• To reduce the risk of injury due to the size and weight of the device, keep the device upright.
• When placing the device onto the mount, be certain it is properly seated before releasing it.
• Keep the assembly area clear of packing materials. Remove materials after each step.
WARNING: Designated load capacity
Wall mounts are rated for a designated load capacity. To reduce risk of personal injury, death, or damage to the device, never exceed the designated load capacity of the wall mount. Refer to the specification section for
weights and load capacities.
WARNING: Tip-over and fall hazard
The wall mount is designed to handle the weight of the device. To reduce the risk of injury or death, never allow anyone or anything to hang from the unit. Never suspend anything other than the designated device.
WARNING: Do not attempt to repair or modify
Assemble stand components using only fasteners provided by Microsoft, as shown on the parts list. Do not attempt to take apart, open, service, or modify the product, accessories, or power supply. Doing so could present
the risk of electric shock or other hazard. Any evidence of any attempt to open and/or modify this device, including peeling, puncturing, or removing any of the labels, will void the Limited Warranty. Heed all warnings and
follow all instructions.
WARNING: Electrical outlet location
To reduce risks related to electric shock, ensure that there is an appropriate electrical outlet within reach of the power cord provided with device to be mounted. Do not use extension cords, or a power cord other than
what is provided with the display assembly.
WARNING: Pinch hazard
When mounting the wall support and installing the device, take care to avoid pinching fingers.
WARNING: Choking hazard
This device or its accessories may contain small parts, which may be a choking hazard to children under 3. Keep small parts away from children.
WARNING: Small children
This device and its accessories are not toys. To reduce the potential for injury, death, or product damage, do not allow small children to play with them. Never allow children to climb on or hang from the device or its stand.
WARNING: Mounting surface orientation
The wall mounting assembly is designed for vertical surfaces only. To reduce the risk of injury or death, do not mount to any surface other than a vertical wall. Do not mount in any orientation other than landscape.
WARNING: Ensure screws are securely tightened
To reduce the risk of the product falling, ensure that all screws are securely tightened to their specified torque values. Do not overtighten as this may cause damage and weaken the holding strength.
This guide outlines the steps for assembling the Surface Hub 55" and Surface Hub 84" wall mounts. These mounts require two people to assemble. Before you begin, make sure you have all of the components in the parts
list.
IMPORTANT: Avoid damage to your device.
support it to keep it vertical. The Surface Hub 84" is intended to be supported only by the lifting handles when not supported by the mounting system. Do not place either device on its face, back, top, or sides.
Specifications
Model Device Stand
weight weight
Surface Hub 55" 105 lb. 25 lb.
Surface Hub 84" 250 lb. 35 lb.
Required tools (not included)
• #2 Phillips screwdriver
• 5mm hex key (Surface Hub 55" only)
• 6mm hex key (Surface Hub 84" only)
• 1/2-inch wrench or socket
• Hand Drill
• 7/32-inch drill bit
• 1/4-inch drill bit
• Level
• Stud finder
• Tape measure
• Straightedge
• Eye protection
• Torque wrench with 5mm and 6mm hex bits
2
The Surface Hub 55" is intended to be supported only by its bottom edge when not supported by the mounting system. Rest it only on its bottom edge, and
Handle Designated
weight load capacity
NA 130 lb.
30 lb. 315 lb.
K