Operation; The Hob; Pan Recognition; Operation Time Limit - Teka GKST 3012 Instrucciones Para El Uso Y Montaje

Encimera vitrocerámica per inducción
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 72

Operation

The hob

Operation
The hob is equipped with an induction cooking mode. An
induction coil underneath the glass ceramic hob generates an
electromagnetic alternating field which penetrates the glass
ceramic and induces the heat-generating current in the pot base.
With an induction cooking zone the heat is no longer transferred
from a heating element through the cooking pot into the food
being cooked; instead the necessary heat is generated directly in
the container by means of induction currents.
Advantages of the induction hob
– Energy-saving cooking through the direct transfer of energy to
the pot (suitable pots/pans made of magnetisable material are
required).
– Increased safety as the energy is only transferred when a pot
is placed on the hob.
– Highly effective energy transfer between an induction cooking
zone and the base of a pot.
– Rapid heat-up.
– The risk of burns is low as the cooking area is only heated
through the pan base; food which boils over does not stick to
the surface.
– Rapid, sensitive control of the energy supply.

Pan recognition

If a cooking zone is switched on and there is no pan on the zone
or if the pan is too small, there will be no transmission of power.
The symbol
in the power setting display points this out.
If a suitable pot or pan is placed on the cooking zone, the power
setting will switch on and the power setting display will light up.
The power supply will be cut off when the pan is removed and the
power setting display will indicate
If the pots and pans placed on the cooking zone are of smaller
dimension, and the pan recognition still switches on, less power
will be supplied.
Pan recognition limits
Cooking zone diameter
(mm)
160
200
250
For some of the models the minimum diameter of the base of a
pot is indicated as an inner circle on the cooking zones.
.
Minimum diameter of the
base of a pot (mm)
90
120
160

Operation time limit

The induction hob has an automatic time limit function.
The duration of continuous use of each cooking zone depends on
the cooking level selected (see chart).
This requires that the setting of a respective cooking zone is not
adjusted during use.
If the operation time limit has been activated, the cooking zone
will switch off, a short signal will sound and an H will appear in
the display.
The automatic switch-off function overrules the operation time
limit, i.e. the cooking zone is only switched off when the period of
time of the automatic switch-off device has expired (e.g.
automatic switch-off after 99 minutes and cooking level 9 is
possible).
Power setting
1, 2
3, 4
5
6, 7, 8, 9

Other functions

If two or more sensor keys are pressed at the same time (e.g.
when a pan is mistakenly put onto a sensor key) no function will
be activated.
An acoustic signal sounds and ER03 will appear. After a few
seconds the appliance will switch off. Please remove the item
located in front of the sensor keys.
Protection against overheating
(induction)
If the hob is used at full power for a longer period, it will not be
possible to cool down the electronics system as required at a
high room temperature.
In order to ensure that no excessive temperatures occur in the
electronics system the power of the cooking zones may be
reduced automatically.
Should E2 or ER21 be displayed frequently during normal use of
the hob and at normal room temperature, it is likely that cooling is
not sufficient.
The reason may be that there are no openings for cooling
purposes in the kitchen units. It may be necessary to check the
installation of the hob (see the section on Ventilation).
GB
GB
Operation time limit
in hours
6
5
4
1,5
19

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Gkst 6013Gkst 6014Gkst 8014

Tabla de contenido