Priority Management (Bgsm-120 Series Only); Simulated Telephone Line Priority; Sms Dialer Priority; Dialer Event Priority - Bentel Security BGSM-120 Serie Manual De Usuario

 Alarm indications which may occur on one or more of the 3 programmable input lines. Bear in mind that 2 voice
messages can be recorded for each of the 3 input lines on the device, one for Activation and one for Resetting.
 PSTN line test. 2 voice messages may be recorded: one for PSTN line absence and one for Resetting.
 Power supply voltage test. 2 voice messages may be programmed: one indicating Power supply voltage problems and
one for Resetting.
 Periodic voice message, with a programmable time period between 1 hour and 1 year.
A voice call takes place when an event occurs on a channel for which a voice message and at least one telephone number
has been programmed.
In this case, the Communicator performs the following steps:
1. The Communicator selects a telephone number and forwards the call over the GSM telephone line.
2. The Communicator makes sure that the number is not busy and that there are no problems on the GSM network, so that
it can proceed with the next step, otherwise the call will end and step 1 will be attempted again, up to a maximum of 8 times
(depending on the programmed value). After 8 attempts the call cycle will be considered complete. If the alarm channel
has been programmed to call several telephone numbers, they will be called in a set sequence. By doing this, for
example, the possibility of calling a busy number several times in the space of a few seconds can be avoided.
3. The Communicator waits for a response from the number called for a period of up to 60 seconds. If the outcome is positive,
the Communicator moves on to step 4; otherwise the call will end and step 1 will be attempted again, up to a maximum
of 8 times (depending on the programmed value). After 8 attempts the call cycle will be considered complete.
4. The Communicator plays the message corresponding to the channel where the alarm is taking place, the call is considered
completed only once the message has been received, or when the
selected, see the Voice dialer->Call Confirmation section) on the phone receiving the message. In any case, the call is
considered successful after the message has been repeated up to a maximum of 8 times (depending on the programmed value).
If, at the selection stage, several events occurred causing several different messages to be sent to the same telephone number,
these messages are reproduced (each for a maximum of 8 times, depending on the programmed value) in sequence during the
same telephone communication, thus avoiding calls being made to the same number several times. If at the end of the call cycle,
the line which caused the Communicator to be activated is still in alarm mode, the procedure described above will not be repeated
again. In fact, the line that caused a call cycle must return to standby mode before a new cycle is activated.

Priority management (BGSM-120 series only)

The Communicator can be used to transmit alarm events and SMS or voice messages; several priorities may be programmed
using the BGSM-120/BGSM-100 Console software (please refer to the section corresponding to programming procedures using
the BGSM-120/BGSM-100 Console software). The table below lists the default priority management settings.
Event
priority
1 (HIGH)
2
*3 (LOW)
* The GPRS supervision event has the lowest priority and cannot be programmed using software

Simulated telephone line priority

When the device connected to the LI terminals requests the line, any other call made at that moment in Voice dialer mode
will be terminated. The calls requested by the device connected to the LI terminals (a burglar alarm control unit, for example)
take place in this manner. When the device connected to the LI terminals frees the line, the voice dialer will resume the
suspended calls and begin sending voice messages again.

SMS dialer priority

If a piece of equipment connected to the LI terminals is making a call over the GSM network through this dialer and an SMS
dialer action needs to be performed, the call from the interface will not be terminated and the SMS message will still be sent.

Dialer event priority

The SMS messages have a lower priority than Voice messages but they can not be interrupted while they are transmitted:
in this case, the queued Voice message will be sent at the end of the SMS message sending.
BGSM-100/120
Priority management table
Event description
Request LI line (release)
Voice dialer (voice messages)
GPRS supervision
key is pressed (if "Call Confirmation" has been
Can be programmed
Default settings
using software



Yes
Yes
No
13
G