Seamless Loop/Hot Start And Stutter; Playing Mp3 Files - Denon DN-D4000 Instrucciones De Operación

SEAMLESS LOOP/HOT START AND STUTTER

7
(1) Seamless Loop/Hot Start/Stutter (A1, A2 buttons)
Setting the A point (loading the Hot Start
data)
Push the A1 or A2 button @0 to
set the A point and Hot Start data
A 1
loading starts.
1
• A1 and A2 buttons can be used
separately for each Hot Start.
• When an A point is set, the corresponding
A button light and that button is set to the
Hot Start mode.
Starts Hot Start
When A1 or A2 button @0 is
A 1
2
pushed, Hot Start playback starts
from the corresponding A point.
Setting the B point for Seamless Loop
When the B button @1 is pushed
after setting the A point or after
B
starting Hot start playback, the B
point is set and Seamless Loop
playback starts from the A point.
3
• The B button works with respect to the A
point operated before the B button @1 was
pushed.
• If the B button @1 is pushed during
seamless loop playback or after EXIT
playback, the B point moves to the point at
which the button was pushed.
Playing seamless loops
• When the B point for A1 is detected after
playback started from A1 point, playback
returns to A1 point with seamless. While
4
A1 to B looping, B point for A2 ignored.
• When the B point for A2 is detected after
playback started from A2 point, playback
returns to A2 point with seamless. While
A2 to B looping, B point for A1 ignored.
Exit/Reloop
In Seamless Loop playback, you
EXIT/
RELOOP
can force exit from or return in the
loop.
EXIT:
While the Seamless Loop playback, push the
5
EXIT/RELOOP button @2 to exit from loop.
DN-D4000 continues playback after the B
point.
RELOOP:
When the EXIT/RELOOP button @2 is pushed
after exit the loop, Seamless Loop playback
resumes from the A point.
Stutter
• A1 and A2 points can be also used for
Stutter playback.
6
To enable stutter playback, push
FLIP
FLIP button !9 for A1/A2 buttons.
Push the FLIP button !9 to switch
between the Hot Start/Seamless
Loop and Stutter modes.
Clear the A1/A2 point
While pushing the FLIP button !9 , push the A1
or A2 button @0 to clear the corresponding A
and B points.
Or push the Flip button !9 for more than 1
7
second to clear both A1 and A2 points at once.
FLIP
A 1
(2) Fine-adjusting the start points (A-1 and A-2) and end point (B)
• The A-1, A-2 and B points can also be adjusted in the standby mode at their respective points.
Adjust the start point (A).
To fine-adjust the position of the A-1 (or A-2)
point once it has been set, in the standby
mode press and hold down the CUE button !0
then push the "A" button @0 that you wish to
edit.
1
A 1
• The standby mode is now set to edit/fix
either A-1 or A-2 points.
Use the Jog/Shuttle wheel y, !7 to manually
search through the track in order to find your
desired new start point. When found, press
the same "A" button @0 to resave.
2
SEARCH SCAN
6 7
A 1
8

PLAYING MP3 FILES

The music on commercially available music CDs can be converted into MP3 files on a computer using MP3
encoding programs. When this is done, the data is reduced to approximately 1/10 the original size. This MP3 data
can then be stored on a CD-R/RW disc, allowing you to create a single 12 cm CD-R/RW disc containing about 10
times more music than a normal music CD, that is some 100 tracks or more (*).
* This is an approximately value for MP3 files of tracks about 5 minutes long converted at a standard bit rate
(128 kbps) and stored on a CD-R/RW disc with a capacity of 650 MB.
Recordings you make are for your personal use and should not be used in ways infringing upon the copyright
holder as per copyright laws.
MP3 may require time for reading.
With disc condition it may not play properly.
To protect copyrights, no digital signals are output when playing MP3 files.
ENGLISH
Adjust the end point (B).
Follow the same steps from 1 and 2 above,
except, press and hold the CUE !0 button and
then the B button @1 in order to edit your end
B point, Then press the B button @1 again to
3 save your changes.
B
NOTE:
• It is not possible to set an A point at a position
after the B point or the B point at a position
before the A point.
11