Lutron QS DMX Serie Instrucciones De Instalación Y Operación página 4

Programming
Note: For systems controlled by a Quantum
programming is done using the Q-Design
programming section applies only to systems controlled using a
GRAFIK Eye QS control unit.
®
Assigning a Single DMX Channel to a
GRAFIK Eye QS Zone
®
Most DMX fixtures use single-channel assignment. If you are
instructions to the right for 3-channel DMX assignment.
1. Enter programming mode on the
Zone 4
GRAFIK Eye
Setup" then "Load Type" from the Main
DMX Menu. For the zones you wish to assign
to DMX.
2. Exit programming mode on the
GRAFIK Eye
3. Enter programming mode on the
DMX Prog
QSE-CI-DMX: Press and hold the
Push
programming button for 3 seconds.
Zone R to Assign
Zone L to Unassign
any GRAFIK Eye
their status:
and all LEDs of unassigned zones will go to Off. To assign a DMX
GRAFIK Eye QS control unit
®
Zone Buttons
1 9 2 10 3 11 4 12
4. The GRAFIK Eye
Zone 4
selected zone and an unassigned
Choose Channel on
DMX AABB-CCEE
on the GRAFIK Eye
14
DMX channel (from 1 to 512) for this
zone. Press the Scene 1 button on the
GRAFIK Eye
selected DMX channel to flash. Press
OK to assign the selected DMX channel
to the selected zone.
Note: Do not use the Flash feature with DMX devices containing
causing unexpected motion. If the selected channel is already
confirm replacing the channel with the new selection. Press OK
to confirm the replacement.
4
®
software. This
TM
QS. Choose "Zone
®
QS.
®
QS control units on
®
Zone LEDs full on and
flash (zone assigned to
5 13
QSE-CI-DMX)
Zone LEDs Off
(zone unassigned
to QSE-CI-DMX)
QS will display the
®
QS to choose a
®
QS to cause the currently
®
QS will prompt you to
®
5. Repeat step 4 for each DMX zone.
6. Exit programming mode: Press and hold the programming
OK
Assigning RGB/CMY DMX Channels
(3-Channel DMX) to GRAFIK Eye
1. Enter programming mode on the
Zone 4
GRAFIK Eye
Setup" then "Load Type" from the
Main Menu. For the zones you wish to
RGB/CMY DMX
the load type to RGB/CMY DMX.
2. Exit programming mode on the
GRAFIK Eye
3. Enter programming mode on the
Zone 4- RGB/CMY
QSE-CI-DMX: Press and hold the
programming button for 3 seconds.
Component 1 channel
14
On any GRAFIK Eye
their status: LEDs of assigned zones
of unassigned zones will go to full off
(all LEDs off). To assign a DMX Channel
4. The GRAFIK Eye QS will display the selected zone and an
®
GRAFIK Eye QS to choose a DMX component channel (from 1
®
to 512) for this zone. Press the Scene 1 button on the GRAFIK
Eye QS to cause the currently selected DMX channel to flash.
®
Press OK to assign the selected DMX channel to the selected
zone and proceed. Repeat for all 3 channels.
Eye QS will prompt you to confirm replacing the channel with
®
the new selection. Press OK to confirm the replacement.
5. Repeat step 4 for all the RGB/CMY DMX zones.
6. Exit programming mode: Press and hold the programming
Note: The RGB/CMY table can be edited to map a zone
intensity to a specific RGB/CMY color using the color
configuration tool for the QSE-CI-DMX (available at
www.lutron.com/qs).
Master buttons
OK button
Scene 1 button
QS Zones
®
QS. Choose "Zone
®
QS.
®
control units on
®