Wheels; Dust Bag; Lubrication; Service And Spare Parts - Bona Edge UX Manual De Funcionamiento Y Mantenimiento

Routine Maintenance (Cont.)

Wheels

Remove dirt from the machine unit and wheels regularly. Dirt may cause uneven sanding.

Dust bag

Remove the bag and shake it well, using a mask and safety goggles, to remove sawdust. It is recommended to properly
dispose of the sawdust. Turn the bag inside out and wash it in the machine in cold water to prevent blockage of the pores
and a decrease in dust collection ability.

Lubrication

The machine does not require lubrication. All moving parts, including the motor, have watertight ball bearings lubricated for
approximately 10,000 hours of operation.

Service and Spare Parts

Service

Bona Edge UX is a high quality machine and is tested by authorized test staff at the factory before delivery. However, electrical
and mechanical parts wear down and age during long-term use.
Only Bona's original parts may be used because the machine is considered unique, otherwise safety functions can become
impaired.
When you contact Bona or staff approved by Bona in the event of a fault or to order spare parts, always specify the type and
serial number of your machine. This information is located on the data plate of the machine.

Spare parts and exploded views

On the Internet, you will find a list of spare parts and exploded views for Bona Edge and other machines in our product range.
Visit http://spareparts.bona.com/
During the factory warranty period, repairs may only be carried by Bona or staff approved by Bona. Other repairs (after the
warranty period) of mechanical or electrical parts on the machine may only be carried out by Bona or staff approved by Bona
who has experience and knowledge concerning safety regulations.
20

Troubleshooting

Bona Edge UX
PROBLEM
Motor does not start
Insufficient motor speed
Insufficient cutting
The Velcro backing disc wears-out
too quickly
Scratched work surface
Scorching on work surface
Insufficient dust collection

Hour Meter Display Notices

ANZEIGE
ERR 100
ERR 200
ERR 300
PRESS LEVER
CAUSE
No power supply voltage Check power supply or try on a different job-site
They must be checked and arranged (contact an authori-
Unstable connections
zed Bona dealer)
Faulty switch It must be replaced (contact an authorized Bona dealer)
Burnt rotor It must be replaced (contact an authorized Bona dealer)
Faulty motor It must be replaced (contact an authorized Bona dealer)
Excessive cable length or unsuitable cross
Change it
section
They must be checked and arrangged (contact an autho-
Unstable connections
rized Bona dealer)
Worn-out carbon brushes Replace them
Burnt rotor It must be replaced (contact an authorized Bona dealer)
Faulty motor It must be replaced (contact an authorized Bona dealer)
Unsuitable or worn abrasive Replace the abrasive
Worn-out driving belt or pulleys or bearings Replace them (contact an authorized Bona dealer)
Avoid exerting excessive pressure: the plate overheats
Pressing on the arm while sanding
causing premature consumption
Faulty abrasive Replace the abrasive
Disc surface dirty, faulty or worn Clean or replace the disc
Incorrect wheels adjustment Correct the wheels position
Worn-out driving belt or pulleys or bearings Replace them (contact an authorized Bona dealer)
Worn or abrasive too fine Replace the abrasive
Check and adjust the wheels position / Don't press on
Excessive pressure on the disc
the arm while working
Dust bag more than 1/3 full Empty the bag
Dust bag dirty or with blocked pores Shake out the dirt and wash the bag
Vacuum ducts and/or pipes obstructed Clean air ducts
They must be replaced (contact an authorized Bona
Worn-out bearings or suction fan
dealer)
MÖGLICHE URSACHE
The current absorption is too high (Rotor block intervention)
The machine is too inclinated (Inclination sensor intervention)
Accelerometer hardware error
If press the contact switch before to press one of the red levers
EN
Bona Edge UX
SOLUTION
21