Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTION
REqUIREMENTS
This appliance must be installed and grounded on a branch
circuit by a qualified technician in accordance with the
National Electrical code ANSI/NFPA NO. 70 - latest edition.
All wiring should conform to Local and NEC codes. This
range requires a single-phase, 3 wire, AC 120/208V or
120/240V 60Hz electrical system. Use only a 3-conductor
or a 4-conductor UL-listed range cord with closed-loop
terminals, open-end spade lugs with upturned ends, or similar
termination. DO NOT install the power cord without a strain
relief.
A range cord rated at 40 amps with 120/240 minimum volt
range is required. If a 50 amp range cord is used, it should be
marked for use with 1
/
" diameter connection openings.
3
8
This appliance may be connected by means of conduit or
power cord. If conduit is being used, go to page 9 for 3
wire conduit connections or page 10 for 4 wire conduit
connections.
WARNING
• New branch-circuit installations (1996 NEC) for
mobile homes, recreational vehicles, and installations
where local codes do not allow grounding through
the neutral wire require a 4-conductor UL listed
range cord or 4 wire conduit connection.
• Power supply cord and plug should not be modified.
If the plug will not fit in the outlet, have a proper
outlet Installed by a qualified electrician.
• Do not use an extension cord to connect to power.
Connect the power cord and plug directly.
• Electrical ground is required on this appliance.
• Make sure that the power cord is not pinched by the
range or heavy objects.
− Failure to do so can result in serious burns or
electrical shock.
Specified power-supply-cord kit rating
Range rating, watts
Specified rating
of power-
supply- cord
120/240 volts
120/208 volts
kit, amperes
3-wire
3-wire
8,750 -
7,801 -
40 or 50A
16,500
12,500
16,501 -
12,501 -
22,500
18,500
3, 4 - Wire electrical wall Receptacle
4 Wire receptacle (14-50R)
3 Wire receptacle (10-50R)
FIGURE 3
Diameter (inches) of Range
connection Opening
Power cord
Conduit
1
3
/
"
1
1
/
"
8
8
50
1
3
/
"
1
3
/
"
4
8
ELECTRICAL CONNECTIONS
CONNECT RANGE CORD
WARNING
• Do not operate the range without the protective
covering on the rear of the lower oven in place.
− Doing so can cause serious damage to the power cord,
resulting in severe burns and electric shock.
The rear access cover must be removed. Loosen the three
screws with a screwdriver. The terminal block will then be
accessible.
Cord/Conduit
connection
Rear of lower oven
plate
FIGURE 4
Use the cord/conduit connection plate to install the power
cord or conduit. Leave the connection plate as installed for
power cord installations. Remove the connection plate for
conduit installations and use the smaller 1 1/8" (2.8 cm)
conduit hole instead of the 1 3/8" (3.5 cm) power cord hole.
1
3
/
"
8
(Cord)
1
1
/
"
8
(Conduit)
Remove the conduit connection plate
FIGURE 5
Strain relief
Conduit
Ring
Conduit
Body
Cord Strain
relief
Reinstall the cord/conduit connection plate
FIGURE 6
7
Terminal block
Access cover
Protective cover
Access
cover
1
/
"
1
8
(2.8cm)
1
3
/
"
8
(3.5cm)
Cord/Conduit
connection
plate
Assemble the
strain relief hole
Publicidad
Tabla de contenido
