Select Blower Option And Install Ductwork; Prepare The Installation - Broan-NuTone RANGEMASTER RMIP33 Manual Del Usaurio

1. SELECT BLOWER OPTION AND INSTALL DUCTWORK

Either an interior or exterior blower may be used with this insert. The insert model RMIP33 or RMIP45 must
be installed with blower models P5, P8, 331H, 332H, 335 or 336 only. Other blowers cannot be substituted.
(Blowers sold separately).
NOTE: The 331H, 332H, 335 or 336 exterior blower MUST BE installed with the rough-in kit model 332KR
(sold separately).
Plan where and how the ductwork will be installed. Access to the top of the hood is preferred for connection
of ductwork. As an alternative, flexible metal ductwork may be used.
Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Use round
ductwork, with a short section (about 4' expanded) of flexible metal duct (optional) for attachment to the
transition. Use screws to attach flexible metal duct to the rigid duct. Use 2" duct tape to seal duct joints.
The minimum hood distance above cooktop must not be less than 24". A maximum of 30" above
cooktop is highly recommended for best capture of cooking impurities.
Distances over 30" are at the installer and users discretion.
Roof cap
7" or 8" round ducts
with 7" or 8" round
metal flex. duct (optional)
3 1/4" x 10" to 7" or 8" transition
or 3 1/4" x 14" to 8" transition
Insert with
Wall
interior blower
cap
24" minimum
above cooking surface
HH0038A
MODEL P5 (SINGLE) OR P8 (DOUBLE)
INTERIOR BLOWER TYPICAL DUCTWORK

2. PREPARE THE INSTALLATION

Make sure that the following items are included:
- Insert
- Accessories:
• Filters (3 for RMIP33 model and 4 for RMIP45 model)
• Bag of parts including:
(4) lock nuts, (1) wire clamp, (8) #8 x 3/4" standard screws, (2) wire connectors,
(2) #6 x 1/2" standard screws, (8) #8 x 3/8" screws. Discard items not used.
Parts sold separately:
- Interior blower Model P5 includes blower, rough-in kit, flow deviator and 3 1/4" x 10" adapter
- Interior blower Model P8 includes blower, rough-in kit, flow deviator and 3 1/4" x 10" adapter
and 3 1/4" x 14" adapter
- Exterior blower Model 331H, 332H, 335 or 336
- Exterior blower rough-in kit Model 332KR (required for all exterior blower models)
- Halogen lights (120V, 50W, PAR 20) (2 for RMIP33 model and 3 for RMIP45 model)
- Custom hood liner Model RML3336, RML3336S, RML3342, RML3342S, RML4548, RML4548S,
RML4560 or RML4560S (optional)
- Backsplash RMP Series (optional)
- RMIPWC Remote control (optional)
- Baffle filters RBFIP Series (optional)
- Transitions, ducts (rigid and flexible), elbows, dampers, wall and roof caps. Refer to page 3 for a complete
list of venting options and model numbers.
NOTE: During installation, protect countertop and/or cooktop.
Exterior blower
HH0039A
MODEL 331H, 332H, 335 OR 336 EXTERIOR
BLOWER TYPICAL DUCTWORK
- 4 -
10" round duct
10" round metal flex. duct
(optional)
Insert with
exterior blower
24" minimum
above cooking surface