Worx WG156 Manual Del Usuario página 11

AssEMBLY
1. aSSEmBly oF THE SaFETy GuaRd
(See Fig. a1, a2)
Remove a screw from the guard; attach the
safety guard to the trimmer head. Align the
guard so it slides into the slots located on the
trimmer head. Turn the tool over and secure
the safety guard onto the trimmer head with
the screw (a) provided.
2. aSSEmBly oF THE EdGER wHEEl
(See Fig. B1, B2))
With the tool rightside up, slide the edger
wheel assembly onto the metal plate located
on the side of the trimmer head. Make sure the
groves of the edger wheel assembly locks onto
the metal plate, you will hear it click into place.
To remove the wheel assembly, press the
release button (b) on the wheel and pull the
wheel assembly upward.
3. FiTTiNG THE auxiliaRy HaNdlE
(See Fig. C1,C2)
NoTE: THE auxiliaRy HaNdlE muST BE
aTTaCHEd to the trimmer shaft before use.
waRNiNG: To avoid injury, alwayS
remove the battery pack BEFoRE
installing parts or cleaning the trimmer
or making any adjustments.
1) Unscrew the auxiliary handle's tightening
knob (counter-clockwise) and remove from
handle.
2) Position auxiliary handle onto handle
bracket assembly located on trimmer's top-
shaft (See Fig. C1).
3) Position the knob and screw through the
auxiliary handle and bracket, and tighten
knob (turn clockwise). (See Fig. C2) Do not
tighten completely until you have adjusted
the auxiliary handle to your desired working
position.
oPErATIoN INsTrUCTIoNs
waRNiNG! The charger and battery pack
are specially designed to work together so
do not attempt to use any other devices. Never
insert or allow foreign metallic objects into your
charger or battery pack connections because of
2 in 1 Grass Trimmer/Edger
an electrical failure and other hazards that will
occur.
1. BEFoRE uSiNG youR CoRdlESS
GRaSS TRimmER
Your battery pack is UNCHARGED and it must be
fully charged once before it is used.
The battery charger supplied is matched to the
Li-ion battery for use with this tool. Do not use
another battery charger.
2. CHaRGiNG youR BaTTERy PaCk
The Li-ion battery is protected against deep
discharging. When the battery is empty, the
trimmer will switch off by means of a protective
circuit: The trimmer head will stop rotating.
NoTE: In a warm environment or after heavy
use, the battery pack may become too hot to
permit charging. Allow time for the battery to
cool down before recharging.
3. To REmovE oR iNSTall BaTTERy
PaCk (See Fig. d)
Depress the battery release button to remove
battery pack from your trimmer. After recharging,
insert the battery pack onto trimmer's battery
bracket. A simple push and slight pressure will
be sufficient.
4. SaFETy oN/oFF SwiTCH (See Fig. E)
The safety switch is locked off to prevent
accidental starting. Depress the lock off button
(c) then depress the on/off switch (d) and release
lock off button (c). Your trimmer is now on. To
switch off, just release the on/off switch.
waRNiNG! The cutting head
continues to rotate after the trimmer
has been switched off; wait until it has
completely stopped then lay down the
tool.
5. adJuSTmENT oF THE TElESCoPiC
SHaFT (See Fig. F)
Unscrew the locking collar (4) in the direction
indicated to unlock, turn it clockwise.
Adjust the length of the telescopic shaft to the
most comfortable length.
Tighten the locking collar (4) in the direction
indicated to lock, turn it counterclockwise.
11
EN