Worx WG156 Manual Del Usuario página 12

6. maiN HaNdlE RoTaTioN
(See Fig. G1, G2)
While holding the trimmer head (13), pull
upward on the upper shaft (17) and rotate it 90
degrees clockwise then allow it to drop back into
the lower shaft coupling (16). When released
back into the lower shaft coupling, the upper
shaft will be locked into position automatically.
7. adJuSTiNG auxiliaRy HaNdlE
(See Fig. H)
1) The auxiliary handle itself can be moved
forward or backward into 4 different locked
positions (see Fig. H).
2) When the handle is in desired position, turn
knob and tighten securely.
8. adJuSTmENT oF THE TRimmER
HEad aNGlE To THE SHaFT
(See Fig i1, i2)
To adjust the upper shaft angle downwards
or convert the tool from trimming mode to
edging mode, put one foot on the motor
housing portion of the trimmer head (18), then
grip the main handle/upper shaft and apply
12
adequate force on the upper handle pushing it
downwards, as shown in Fig I1.
Adjust the upper shaft angle upwards, put one
foot on the safety guard area of the trimmer
head, then grip the main handle, apply
adequate force to adjust, as shown in Fig. I2.
9. SPaCER GuaRd (See Fig. J)
Push the flower guard in when edging and
pull it before trimming, as shown in Fig J.
Before trimming or edging make sure the
flower guard is locked firmly in position.
oPErATIoN
waRNiNG: Always wear the eye
protection. Never lean over the trimmer
head. Rocks or debris can ricochet or be thrown
into eyes and face and cause blindness or other
serious injury. When operating unit, check for
the following:
Wear eye protection and heavy clothing. Hold
front handle with one hand and auxiliary handle
with the other hand. Keep unit below waist
2 in 1 Grass Trimmer/Edger
level. Work only from your right to your left to
ensure debris is thrown away from you. Without
bending over, keep line near and parallel to the
ground (perpendicular when edging) and not
crowded into material being cut.
waRNiNG: Make sure that line is fed out
before operation. Make sure motor is up to
full speed before trimming or edging.
waRNiNG: Use only 0.065"(1.65mm)
cutting line, diameter line. Other sizes of
line will not feed properly and will result in
improper cutting head function or can cause
serious injury. Do not use other material such as
wire, string, rope, etc. Wire can break off during
cutting and become a dangerous projectile that
can cause serious injury.
TRimmiNG
Hold the bottom of the trimmer head about just
above the ground and at a slight angle. Allow
only the tip of line to make contact with the
grass. Let the trimmer line work at its own pace.
Do not force trimmer line into work area.
EdGiNG (See Fig. k)
Change the tool from trimming to edging
mode by putting one foot on the motor
housing portion of the trimmer head (13) while
gripping the main handle/upper shaft apply
adequate force on the upper handle pushing it
downwards, as shown in Fig I1. Make sure to
adjust trimmer head angle to be in the lowest
horizontal setting., holding the lower housing
then pull upwards the upper shaft, then rotate
90 degree clockwise. (Fig G1)
Then position the wheel on the ground for edge
mode. The guard has two white line guides to
indicate the cutting line position. Align these
marks with the edge of your lawn.
While edging, only allow the tip of the line to
make contact with area being worked. Do not
force the line. The edging wheels help protect
the unit and keep the unit from contacting the
ground. Take extra caution while edging as
objects can be thrown from the trimmer line.
auTomaTiC liNE FEEd SySTEm
When initially switching on the trimmer, a small
EN