Moving The Appliance - TESY MC 20112 Instrucciones De Uso

OPERATION
The heater may be operated by the manual controls
located on the heater (as shown in Figure 6) or by your
remote control.
Figure 6
1. Place the heater on a firm, level surface.
2. Plug the cord set into a fit electrical outlet. Press the
main power switch at the bottom of right housing
(Power switch location see Figure 5). When heater
is power on, the LED display will show the room
temperature.
3. Turn on the heater by pressing the power button
upper control panel, and it is LOW mode, the power
is 750 W. Press the "SET" knob to MIDD mode, the
power goes up to 1250 W.
Press twice times the "SET" knob to HIGH mode, the
power goes up to 2000W.
Press three times the "SET" knob to the AUTO mode. The
heater works at different power which accord to the air
temperature.
•
When the air temperature is lower than 15°C, the
heater will work at HIGH mode automatically.
•
When the air temperature is at 16°C -20°C, the heater
will work at MIDD mode automatically.
•
When the air temperature is more than 21°C below
23°C, the heater will work at LOW mode automatically.
When the air temperature reaches to 25°C, the heater
will cut off automatically. When the air temperature
drop to 23°C, the heater will come back on LOW mode
automatically.
Press four times the "SET" knob to the FROST mode; the
working position is 7°C for air temperature.
4. To turn the Heater OFF, by pressing the Power
button again and turn off power switch.
English
Setting the temperature:
1. To set the temperature, when the LOW or MIDD or
HIGH mode, Press the
control to increase the desired temperature and
press knob or "DOWN-"on remote control to
decrease the desired temperature.
2. When the air temperature reaches 2°C above the set
temperature, the heater will cut off automatically.
3. When the air temperature drop 2°C below the
set temperature, the heater will come back on
automatically.
4. The selected temperature range is 5°C - 40°C.
Timer setting:
1. Timer ON setting: Press the
on remote control one time, the
begin to flicker, and you can press the
"UP+"on remote control,
remote control to increase or decrease the hours.
The timer function allows you to set the length of
operation from 30 minutes to 24 hours. Ready the
setting 3 seconds later, the "ON" will remains lit.
2.
Timer OFF setting: Press the
remote control twice time, the
begin to flicker, and you can press the
"UP+"on remote control,
remote control to increase or decrease the hours.
The timer function allows you to set the length of
operation from 30minutes to 24 hours. Ready the
setting 3 seconds later, the "OFF" will remains lit.
After reach the setting times of OFF, the heater will
stop working and flicker the "End", and hear three
sounds. Press the "ON/OFF:" button, the heater will
start to rework.
Remark: On FROST mode, it can't set the timer OFF or
ON.
Note: It is normal for heater to cycle ON and OFF as it
maintains to set temperature and working mode.

MOVING THE APPLIANCE:

If it is necessary to move the appliance to another
place of operation, switch it off by pulling the power
plug out of the socket, holding the appliance handles
with both hands, move it to its new position, having
in mind that the appliance must get cold (cooled
down) before doing this. Moving hot appliances may
lead to bad consequences for the user like burns or
inflammable materials entering the panel heater during
its movement.
knob or "UP+"on remote
or "TIMER" knob
and "ON" will
knob or
knob or "DOWN-"on
or "TIMER" knob on
and "OFF" will
knob or
knob or "DOWN-"on
Usage and Storage Instructions
EN
5