Product Familiarisation - Silverline 264569 Instrucciones De Seguridad

GB
i. Be especially careful when using a machine for both wood and metal
sanding. Sparks from metal can easily ignite wood dust. ALWAYS clean
your machine thoroughly to reduce the risk of fire
j. Empty the dust bag or container (if applicable) frequently during use,
before taking breaks and after completion of sanding. Dust may be
an explosion hazard. DO NOT throw sanding dust into an open fire.
Spontaneous combustion may occur when oil or water particles come
into contact with dust particles. Dispose of waste materials carefully
and in accordance with local laws and regulations.
k. Work surfaces and sandpaper can become very hot during use. If there
is evidence of burning (smoke or ash), from the work surface, stop and
allow the material to cool. DO NOT touch work surface or sandpaper
until they have had time to cool
l. DO NOT touch the moving sandpaper
m. ALWAYS switch off before you put the sander down
n. DO NOT use for wet sanding. Liquids entering the motor housing can
cause severe electric shocks
o. ALWAYS unplug the sander from the mains power supply before
changing or replacing sandpaper
p. Even when this tool is used as prescribed it is not possible to eliminate
all residual risk factors. If you are in any doubt as to safe use of this
tool, do not use it
Polisher Safety
• Do not use this polisher as an angle grinder
• Always read and understand all information supplied with polishing
pastes before use
• Do not smoke, eat or drink when using this polisher
• Never attach any accessory with a maximum speed lower than the no
load speed of the machine

Product Familiarisation

1 Spindle
2 Spindle Lock Button
3 Front Handle
4 Speed Control Dial
5 Lock-On Button
6 Rear Handle
7 On/Off Trigger Switch
8 Hook & Loop Backing Pad
9 Hook & Loop Polishing Bonnet
10 Hook & Loop Sanding Disc
11 Brush Access Plugs
Included Accessories:
1x hex key
Intended Use
• Multi-purpose rotary polishing machine, used for light to medium
duty polishing and sanding tasks, using suitable polishing bonnets,
compounds and hook and loop sanding discs
6
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all
its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Before Use
Assembling the front handle
• The Front Handle (3) must be fitted to the machine before use:
1. Use the bolts supplied to fit the Front Handle (3) via the fixing holes to
either side at the front of the machine
2. Use the supplied hex key and tighten the bolts firmly, to secure handle
in position
Fitting the Hook & Loop Backing Pad
• The Hook and Loop Backing Pad (8) must be securely fitted to the
Spindle (1) before use:
1. Press and hold the Spindle Lock Button (2) with one hand, and slowly
rotate the spindle with the other hand, until you feel it lock
2. The backing pad can now be screwed onto the spindle and tightened
WARNING: The backing pad is tightened by hand. Take care not to cross-
thread or over-tighten.
3. Release the spindle lock button
Fitting bonnets, polishing sponges and discs
• The Hook and Loop Polishing Bonnet (9), Hook and Loop Sanding Disc
(10) and other polishing accessories, such as polishing sponges (not
included) can be pressed onto the face of the Hook and Loop Backing
Pad (8)
• Slowly pull the fitted attachment off the hook and loop backing pad
to remove
Note: Always make sure both hook and loop surfaces are free of dirt
and debris prior to attaching any items (also see remarks 'Maintenance'
section).
Operation
WARNING: Always wear adequate protective equipment, including eye,
hand and hearing protection, when operating this machine. Use respiratory
protection where dust or fumes are produced.
Switching on/off
WARNING: Never switch the tool on or off when it is in contact with
the workpiece. This can cause serious injury to the operator and will
significantly shorten the service life of the On/Off Switch (7).
1. Connect the machine to the mains power supply
2. To start the machine, squeeze the On/Off Trigger Switch (7); the motor
will start and take a few moments to reach full operating speed
3. To stop the machine, release the on/off trigger switch
4. To operate the tool's lock-on function, depress the Lock-On Button (5)
whilst holding the On/Off Trigger Switch
5. To stop the tool once locked-on, squeeze and release the
On/Off Trigger Switch
WARNING: ALWAYS wait until the machine has come to a standstill before
putting it down.