Technical Characteristics - Truper COMP-POR-2.5 Instructivo

TECHNICAL CHARACTERISTICS:

Voltage: 120 V~
Frequency: 60 Hz
Current: 7.2 A
Speed: 3 400 RPM
Motor Rated Power: 1.5 Hp
Maximum Motor Power: 2.5 Hp
Maximum Pressure: 116 PSI
IP Grade: IP20
Air Flow: 4 CFM - 40 PSI
3 CFM - 90 PSI
Power Cord Grips Type: Y
All conductors are: 14 AWG x 3C with 221 ºF insulating
temperature
Build quality: Basic insulation.
Insulation quality: Class l
Thermal insulation of motor winding: Class B
To avoid risk of electrical shock or serious accident,
CAUTION
if power cord gets damaged it shall be repaired by the
manufacturer or by Truper
Power cord grips used in this product: Type"Y".
Assembly design in this product causes insulation to be affected
by liquid spills or splashing.
Before gaining access to terminals, all
WARNING
power circuits shall be disconnected.
We do not recommend using power cord
WARNING
extensions with compressors. Using that type of
extension cause power drops resulting in motor potency loss
and overheating. Instead of using an extension cord increase
the compressor's action scope connecting a longer hose into
the outlet. Connect additional hose lengths as needed.
DESCRIPTION
Compressors not using oil are designed for the "Do It Yourself"
mode for a large variety of jobs at home and for automobiles.
This type of unit works with no oil. Compressed air produced
in this tool could cause humidity. Set a water filter or a dryer
if the application needs dry air.
ADDITIONAL SAFETY GUIDELINES
This MANUAL has important information that shall be
understood and learnt. This information is meant for your
SAFETY and to PREVENT PROBLEMS WITH THE UNIT. To learn
about this information follow the following symbols:
Indicates an imminent dangerous situation which
CAUTION
if not avoided could cause death or important injury.
Indicates a potentially dangerous situation which
WARNING
if not avoided could cause death or important injury.
NOTE: Indicates there is important information which if not
followed COULD damage the unit.
ALERT: Do not operate the unit if damaged during shipment.
Damaged units could cause explosion, and damage to property
and injuries to user.
Breathing air alert. This compressor is not built
WARNING
and should not be used to deliver high-quality breathable air.
SPECIFIC SAFETY INSTRUCTIONS
Since the air compressor and other components could produce
high pressure pumping, please use care and follow these caution
measures:
2
Authorized Service Center
®
1. Follow all local safety and electricity regulations.
2. Only people agreeing to follow this safety operation rules
shall use the compressor.
3. Inspect regularly all the brackets for an adequate adjust.
The compressor parts might be hot even tough
WARNING
the unit is no longer being operated.
4. Keep fingers away while using the compressor. Moving and
hot parts are a hazard of injuries and / or burns.
5. If the unit starts vibrating abnormally TURN OFF the motor
and immediately double-check what is the cause. Usually
vibrations could mean a dangerous situation.
Never remove or try to adjust the safety valve.
WARNING
Keep the safety valve free of paint or any other type of
accumulation.
NOTE: Do not spray flammable materials near flames or
explosive sources, including the compressor.
6. Do not smoke when spaying flammable substances.
7. When spraying wear a mask. Work in ventilated areas to
prevent health problems and fire.
8. Do not aim spraying materials towards the compressor. Set
the compressor as far away as possible from the spraying
area to minimize substance accumulation into the
compressor.
9. When spraying or cleaning with solvents or other toxic
chemical substances follow the instructions indicated by
the chemical substance manufacturer.
ASSEMBLY
Important: Set the compressor in a ventilated, clean area where
room temperature is not higher than 98.6 ºF
Set the compressor where there is 18" minimum space around
it and the wall. Objects up close may block ventilation.
Do not set the compressor air intake near areas
WARNING
exposed to fumes, paint, sand or any other type of
contamination. These types of substances could damage the
motor.
WARNING
This unit SHOULD BE USED
with 115 V
~
tension. Using a different
TENSION WILL SEVERELY
DAMAGE the unit.
CONNECTION TO THE MAIN POWER SUPPLY
The compressor shall be set as close as possible to the main
power supply. Double-check the power supply matches the
voltage indicated in the motor nameplate.
This unit must be grounded.
WARNING
The power cables are coded with the
CAUTION
following colors:
GREEN AND YELLOW
BLUE
BROWN
This tool is in compliance with
the Official Mexican Standard
(NOM - Norma Oficial Mexicana).
feeding
to 125 V ~
GROUND
NEUTRAL
CURRENT
CURRENT
GROUND