Bpt OPHERA Instrucciones Para La Utilización Y Instalación página 5

2
B
1
A
>2 cm
R A
H E
O P
R A
H E
O P
tedly, alternated with a short audible signal. To
listen to the next melody, press the auxiliary button
2 ( ) ( in the OPHERA/B model) during the
pause between the audible signal and melody.
Repeat the operation until you hear the melody you
want.
To save the new setting without programming
anything else, press the button
door lock release button
gramming procedure.
B - Programming of melody associated with doorbell
The first doorbell melody is played repeatedly, alter-
nated with two short audible signals.
To listen to the next melody, press the auxiliary but-
ton 2 ( ) ( in the OPHERA/B model) during the
pause between the audible signal and melody.
19
Repeat the operation until you hear the melody you
want.
To save the new setting without programming
anything else, press the button
door lock release button
gramming procedure.
C - Programming of number of rings announcing a call
Three short audible signals sound.
Decide how many rings you want and press the auxi-
liary button 2 ( ) ( in the OPHERA/B model) the
corresponding number of times (in the range 1 to 6).
In system 300 installations, you can increase the
number of rings to a maximum of 51 by customizing
control unit XA/300LR.
3 s after the button was last pressed, you will hear
the call selected for the chosen number of rings.
If you want to save settings without programming
anything else, press the button
door lock release button
call melody programming procedure again.
NOTE. When you exit programming mode, the last
settings selected for each programming procedure
are saved. For a setting to be taken as selected, you
must have heard it at least once.
To repeat the procedure to enter programming
mode, press the button
WARNING. In installations with XA/300LR we
recommend you gather up the receiver's ID (SN)
codes, applied on the outside of the housing, and
enter them in the tables that come with the
XA/300LR, MPP/300LR and IPC/300LR.
Function of each terminal (fig. 8)
Terminal block M1
20
power supply local
from 12÷16 V AC or 14÷18 V DC
B X1 line
+
doorbell input
–
AL alarm input (active to earth)
Technical features
• Video signal system: PAL/NTSC.
• Display: 3,5" colour LCD TFT.
• Supply voltage: local 12 to 16 VAC or 14 to 18
VDC, centralized 14 to 18 VDC.
• Power supply from BUS: 15÷20 VDC.
• Current demand: 400 mA max. (<1 mA quie-
scent).
• Number of receivers activated at the same time
by X1 BUS: 1.
21
• Maximum number of receivers that can be con-
nected to control unit XA/300LR: 100.
• Maximum number of receivers that can be con-
nected to an X1 entry panel: 64 (100 with
XAS/301).
• X1 connection line: non polarized twisted pair
Z=100 Ω.
• Working temperature range: 0 °C to +35 °C.
INSTALLATION
WARNING. It is recommended to install the
monitor in a dry place.
PHI embedding box
The embedding box can be installed in either
masonry or plasterboard walls at a height that is
suitable for the user (fig. 9-10-11).
Make sure the UP indication is facing the right way
indicated on the bottom of the embedding box.
22
- Dimensions: 130x114x53,5 mm.
Masonry wall installation
The embedding box should be installed flush with
the wall, and equipped with the provided protection
(fig. 13) to be found in the packaging (fig. 12).
Installation on plasterboard walls
Press the box against the wall to get four reference
; or press the points where the holes with a 10 mm diameter will
to access the next pro- be made (fig. 14).
Cut the plasterboard to obtain the hole where the
box will be inserted (fig. 15).
Remove the three tabs as shown in figure 16.
Insert the upper part A of the fastening clamps into
the box, leaving the lower part B free (fig. 17).
Place the embedding box into the hole and then
apply the lower part B (fig. 18).
Secure the box to the wall with the screws provided
(fig. 19).
If the wall is more than 2 cm thick, the two parts of
the fastening clamps will need to be separated,
; or press the positioning the lower part B as shown in figure 20.
to access the next pro-
OPHERA and OPHERA/B video handset
Remove the two covers as shown in fig. 21. Wire the
connections.
Fasten the appliance to the embedding box, using
the screws provided (fig. 22).
Insert the covers as shown in fig. 23.
Replace the covers
The appliance is equipped with 3 sets of exchan-
geable covers in different colours.
To replace, proceed as shown in fig. 21 and 23.
DISPOSAL
; or press the
Do not litter the environment with packing material:
to enter the entry panel make sure it is disposed of according to the regula-
tions in force in the country where the product is
used.
When the equipment reaches the end of its life
cycle, take measures to ensure it is not discarded in
the environment.
The equipment must be disposed of in compliance
with the regulations in force, recycling its compo-
and wait at least 5 s.
nent parts wherever possible.
Components that qualify as recyclable waste fea-
ture the relevant symbol and the material's abbre-
viation.
D
HINWEISE FÜR DEN NUTZER
- Bei Störungen, Änderungen oder Reparaturen
an den Geräten (Netzgerät, usw.) nur an Spezia-
listen wenden.
VIDEOSPRECHGERÄT/FARBE
FREISPRECH OPHERA
Videosprechgerät mit Freisprechfunktion Gerät
OPHERA zur Verwendung in den Videosprechanla-
gen der Serien 300, X2, X1 und XUP. In den Video-
sprechanlagen XUP muss die entsprechende
Schnittstelle angeschlossen werden.
Die Installation muss in einem PHI UP-Kasten dur-
chgeführt werden.
Im Gerät ist ein bewegliches, nach aussen um 20°
neigbares Teil vorhanden (Abb. 1).
Das Videosprechgerät ist für den Einbau eines bei-
liegenden Tastenzubehörteils vorgerüstet, durch
das eine Erweiterung mit Nebensprechstellen
möglich ist.
Es ist mit folgenden Steuerbefehlen und Einstellun-
gen ausgestattet (Abb. 2):
BEDIENUNGS- UND
INSTALLATIONSANLEITUNG
Aktivierung/Abschaltung der Sprechstelle
(LED rot)
Türöffner (LED grün) ( 1 )
Mute (LED rot)
Einschaltung und Auswahl der
Außenstation ( 2 )
Zusatz 1 ( 3 )
5