Braun 9 Serie Manual Del Usuario página 11

Battery status
Plug reminder
(low charge / cordless operation only)
Travel lock
Replacement indicator
for Foil & Cutter cassette
Cleaning indicator
(with Clean & Charge station usage only)
*not with all models
Usage
Make sure that the shaver is disconnected from the
power supply. Press the on / off button (4) to
operate the shaver.
Tips for a perfect shave
1. Position the shaver at the right angle (90°)
to your skin.
2. Stretch your skin slightly with your hand.
3. Shave against the direction of your beard growth.
Multi Head Lock switch (head lock)
The shaver head can be locked in five positions to
shave hard-to-reach areas (e.g. under the nose).
90604906_93XXs_SOLO_W&D_Euro_Type_5793_S6-104.indd 11 90604906_93XXs_SOLO_W&D_Euro_Type_5793_S6-104.indd 11
Business Use - P&G AUTHORIZED POA-00101223 Rev 001 Effective Date 2019-01-23 Printed 2019-08-27 Page 11 of 104
The battery status is shown
with segments and additionally
in digits (for some models also
with a battery icon).
• The status segments appear /
disappear gradually with the
status of the battery power.
• The digital number shows the
remaining shaving time in
minutes.
1. Flashing: Battery is in low
charge, i.e. 5 minutes
shaving time are left.
2. Fast flashing: This appliance
can only be operated
cordless. Disconnect the
shaver from the power supply
before turning it on.
When the travel lock icon
appears on the display, the
shaver is locked.
The replacement indicator
shows the usage of the
Foil & Cutter cassette. The
status segments disappear
gradually with the numbers of
shaves*.
The cleaning indicator lights
up after each shave as
a reminder that the shaver
should be cleaned in the
Clean & Charge Station.
• Slide the Multi Head Lock switch (3) down to lock
the shaver head.
• Move the shaver head manually to your desired
position.
Precision trimmer
The trimmer can be used to trim sideburns, mous-
tache or beard.
• Press the release button (8) and slide the trimmer
(6) upwards.
Travel lock
The shaver can be locked to avoid unintended
starting of the motor (e.g. for storing in a suitcase).
• Press the on / off button (4) for 3 seconds to lock /
unlock the shaver. This is confirmed by a beep
sound and the lock icon appearing / disappearing
on the display.
Foil replacement
To maintain 100% shaving performance, replace the
Foil & Cutter cassette (1), when the foil replacement
indicator lights up (and no status segments are
visible).
• To remove the Foil & Cutter cassette press the
release button (2).
• Press the on / off button for 8 seconds to reset the
counter.
• Afterwards you need to unlock the shaver
(see chapter «Travel lock»).
• On some shaver models the replacement indicator
will reset automatically after 7 shaves.
Cleaning
Cleaning under running water
Especially important after foam or gel usage
• Switch on the shaver cordless and rinse the
shaver head under hot running water until all
residues have been removed. You may use liquid
soap without abrasive substances. Rinse off all
foam and let the shaver run for a few more seconds.
• Next, switch off the shaver, press the release
button (2) to remove the Foil & Cutter cassette (1)
and let it dry.
• If you regularly clean the shaver under water,
apply a drop of light machine oil on top of the
Foil & Cutter cassette once a week.
The shaver needs to be cleaned under running
water after each foam or gel usage!
Cleaning with a brush
• Switch off the shaver. Remove the Foil & Cutter
cassette (1) and tap it out on a flat surface. Using
the brush, clean the inner area of the pivoting
head. Do not clean the cassette with the brush as
this may damage it!
11
18.01.19 10:34 18.01.19 10:34