Led Indicators - Mitel MiVoice 6930 Guia De Instalacion

Hardware Features (See Figure
Feature Description
LED indicator Blue - Indicates the status of the handset.
Green - Indicates the status of the handset battery.
Hookswitch key Lifting the handset from the cradle activates the handset. If the
handset is already out of the cradle, pressing the Hookswitch key
is equivalent to taking the handset off hook.
Pressing the key again is equivalent to placing the handset on
hook.
Pressing the Hookswitch key while on a speakerphone call moves
the call to the handset.
Mute key Mutes the handset microphone so that your caller cannot hear
you.
Volume control Adjusts the volume for the handset. Press the key above the Mute
keys key to increase the volume and press the key below the mute key
to decrease the volume.
NOTE: The Mitel Cordless Bluetooth Handset must be fully charged before
use. This will typically take three hours. A new, fully-charged handset battery
has a talk time of six hours.

LED Indicators

The Mitel Cordless Bluetooth Handset has two LEDs:
• Blue – indicates the operational status of the handset.
• Green – indicates the status of the electrical charge of the battery.
LED color, states, and indicator descriptions are as follows:
LED *LED Indicates
Color State
Blue Blinking The handset is not connected and is in pairing mode.
(Handset
Winking The handset is connected but not in use.
not in
cradle)
Fading The handset is connected and in use.
Green Solid The battery is fully charged.
(Handset
Winking The battery is charging.
in cradle)
Note: It is normal for the handset LED to cycle between
winking and solid as battery charge is maintained.
Off When the handset is cradled and the LED does not flash or
illuminate, this indicates an absence of battery power. During
the first 30 to 60 minutes that the light is off, the battery may
be trickle charging. If that is the case, the LED will resume
normal behavior within that 60 minute period. If the LED
remains off for more than 60 minutes, then either the battery
is no longer chargeable or there is a problem in the charging
circuit.
*NOTE: Blinking denotes the LED is alternating very quickly between on and
off. Winking denotes the LED is alternating between being on for a short period
of time and then off for a longer period of time. Fading denotes the LED is
alternating between fading in and out.
Bluetooth Handset Battery Level Display
The battery level of the Bluetooth handset is indicated on-screen in the
following:
• icons in status bar
• warning/critical level toaster notification
• warning/critical indication on the screen saver
A
)
Alerting Tones
The Mitel Cordless Bluetooth Handset provides the following alerting tones:
Event
Power OFF
Mute key on handset ON
Powering On/Off the Handset
To power on the Mitel Cordless Bluetooth Handset place the handset on the IP
phone's cradle.
To power off the Mitel Cordless Bluetooth Handset, press the Hookswitch key
for approximately six seconds until the LED indicator turns blue and then turns
completely off.
Pairing the Handset with the Mitel MiVoice 6930 IP Phone
1. Ensure the Mitel Cordless Bluetooth Handset is powered on.
NOTE: To check if the Mitel Cordless Bluetooth Handset is in pairing mode,
take the handset off the IP phone's cradle and check the LED indicator. The
handset's blue LED blinks when it is in pairing mode.
2. Press the (Settings) key on the phone to enter the Static
Settings menu.
3. Navigate to the Bluetooth setting and press the Select softkey.
4. Ensure Bluetooth functionality is enabled. If it is not enabled, press the
Turn On softkey to enable Bluetooth functionality.
5. If required, press the down navigation key to view the list of Available 
Devices.
6. Press the right navigation key to move to the Bluetooth device selection
column.
7. Using the up and down navigation keys, highlight Cordless Handset and
press the Pair softkey. The phone attempts to pair the Bluetooth handset
and if successful, automatically attempts to connect.
NOTE: If pairing or connecting fails, a failed error message displays on screen.
Press Retry to attempt to pair or connect again, or Cancel to cancel the
attempt.
8. Press OK to acknowledge the successful connection. The MWI indicator
on the phone flashes blue when successfully connected and the handset
LED starts to wink. The connected Bluetooth handset is added to the list
of Paired Devices and is ready to use.
Pairing the Handset with the Mitel MiVoice 6940 IP Phone
1. Ensure the Mitel Cordless Bluetooth Handset is powered on.
NOTE: To check if the Mitel Cordless Bluetooth Handset is in pairing mode,
take the handset off the IP phone's cradle and check the LED indicator. The
handset's blue LED blinks when it is in pairing mode.
2. Press the (Settings) key on the phone to enter the Static
Settings menu.
3. Tap the Bluetooth icon.
Tone
Four tones successively decreasing in pitch
Two low pitched tones
3