Worx WG153 Manual Del Usuario página 11

battery pack from your trimmer (Fig.C1). After
recharging, insert the battery pack into trimmer's
battery port (Fig.C2). A simple push and slight
pressure will be sufficient until a click is heard.
NoTE: When removing the battery pack, hold it
firmly to avoid dropping and injury.
4. SAFETy oN/oFF SwiTCH (See Fig. d)
The safety switch is locked off to prevent
accidental starting. Depress the lock off button
(2) then depress the on/off switch (3) and release
lock off button. Your trimmer is now on. To switch
off, just release the on/off switch.
wARNiNG! The cutting head
continues to rotate after the trimmer
has been switched off; wait until it has
completely stopped then lay down the
tool.
OpERATION
wARNiNG: Always wear the eye
protection. Never lean over the trimmer
head. Rocks or debris can ricochet or be
thrown into eyes and face and cause blindness
or other serious injury. When operating unit,
check for the following:
Wear eye protection and heavy clothing. Hold
front handle with one hand and auxiliary
handle with the other hand. Keep unit below
waist level. Work only from your right to your
left to ensure debris is thrown away from you.
Without bending over, keep line near and
parallel to the ground (perpendicular when
edging) and not crowded into material being
cut.
wARNiNG: make sure that line is
fed out before operation. make sure
motor is up to full speed before trimming
wARNiNG: use only 0.065"(1.65
mm) diameter cutting line. Other sizes
of line will not feed properly and will result in
improper cutting head function or can cause
serious injury. Do not use other material
such as wire, string, rope, etc. Wire can break
off during cutting and become a dangerous
projectile that can cause serious injury.
TRimmiNG
Postion the trimmer head as shown in Fig
10 Grass Trimmer/Edger
"
E1for trimming.
Keep the bottom of the trimmer head just
above the ground and at an angle. Allow only
the tip of line to make contact. Do not force
trimmer line into work area.
EdGiNG (See Fig. E1, E2, E3,E4)
AlwAyS REmovE THE BATTERy
PACk BEFoRE AdJuSTiNG THE
TRimmER HEAd PoSiTioN
For edging, position the trimmer head as Fig.
E 2.
To rotate the trimmer head to edging—first
hold the trimmer shaft as shown in fig E 3---
then with your other hand hold the trimmer
head - Push down and rotate 180degrees and
then release- the trimmer will then lock into
the edging position automatically—fig E 4
NoTE: The trimmer head will only rotate in
one direction.
The edge guide helps protect the unit and
keeps the unit from contacting the ground.
Take extra caution while edging as objects can
be thrown from the trimmer line.
AuTomATiC liNE FEEd SySTEm
When initially switching ON the trimmer, a
small length of line is fed out.
A 'clattering' noise will be heard when the
lines hit the line cutter. DO NOT BE ALARMED,
this is normal. After about 5 seconds the line
will be cut to the correct length and the noise
will reduce as the motor receives full speed.
If the noise of the line being cut can't be heard,
more line will need to be fed out.
To feed more line, it is first necessary to allow
the trimmer to stop completely, then restart,
allowing the motor to reach full speed.
Repeat above until you hear the lines hitting
against the line cutter.
To mANuAlly FEEd THE liNE (See Fig.F1)
AlwAyS REmovE THE BATTERy
PACk BEFoRE AdJuSTiNG THE
TRimmER HEAd PoSiTioN
If required, line can be feed out manually.
To operate, press and release manual line feed
button (13), while gently pulling out the line
until it is long enough to reach the line cutter.
If the line extends past the line cutter, too
11
EN