Error Messages - Sony UP-DF500 Guía De Utilización

Messages
There are two kinds of messages: error messages and
warning messages. This section lists these messages
together with their possible causes and remedies. Note
the messages and act accordingly.
Besides error and warning messages, other messages
stating the operating status of the unit are also displayed.
Those messages are not described here.

Error Messages

If a problem occurs, the ALARM indicator lights and an
error message stating the problem appears on the LCD
window. Note the message and perform whatever action
is necessary to solve the problem.
In the error messages introduced in the following table,
"nn" indicates the number of the symbol displayed in the
actual message.
Error messages Possible causes and remedies
SET FILM The film sheets have run out.
tLoad the film into the film tray.
SET TRAY The film tray is not installed.
tInstall the film tray.
REMOVE PRINTS The maximum number of printouts has
accumulated on the film tray.
tRemove the printouts. Printing
CLOSE COVER One of the front, top, or rear cover is
open.
tClose the opened cover.
REMOVE FILM The film has jammed near the film
TRAY:J0 tray.
tPull out the film tray and remove
REMOVE FILM The film has jammed around the rear
REAR:J1 of the unit.
tOpen the rear cover and remove the
REMOVE FILM The film has jammed between the rear
REAR & TOP:J2 and top of the unit.
tOpen the rear and top covers and
REMOVE FILM The film has jammed around the top of
TOP:J3 the unit.
tOpen the top cover and remove the
REMOVE FILM TOP The film has jammed between the top
& FRONT:J4 and front of the unit.
tOpen the top and front covers and
REMOVE FILM The film has jammed around the front
FRONT:J5 of the unit.
tOpen the front cover and remove
10
Messages
starts again.
the jammed film.(page 12)
jammed film.(page 12)
remove the jammed film.(page 12)
jammed film.(page 12)
remove the jammed film.(page 12)
the jammed film.(page 13)
Error messages Possible causes and remedies
REMOVE FILM TOP The film has jammed around the front
& INNER:J6 or inside the unit.
tOpen the top cover, then the inner
cover and remove the jammed
film.(page 13)
REMOVE FILM The film has jammed near the film
TRAY:J7 tray.
tPull out the film tray and remove
the jammed film.(page 13)
REMOVE FILM The film has jammed at several points.
tOpen all of the covers and remove
SOME PLACES:J8
the jammed film.(page 13)
CALIBRATION The unit takes certain measurements to
INVALID estimate a value for automatic
calibration. However, the correct value
could not actually be measured. The
unit can print, but the automatic
calibration value is not updated.
tTry calibration again. If white strips
or scratches appear on the printout,
clean the thermal head and rollers.
MECHA TROUBLE Mechanical trouble has occurred in the
S nn sensor system of the unit.
tTurn off the power once and then
turn it on. The unit may operate
correctly. However, if the message
still remains on the LCD, turn off
the power immediately and contact
your Sony dealer.
MECHA TROUBLE Mechanical trouble has occurred in the
M nn motor system of the unit.
tTurn off the power once and then
turn it on. The unit may operate
correctly. However, if the message
still remains on the LCD, turn off
the power immediately and contact
your Sony dealer.
MECHA TROUBLE Mechanical trouble has occurred in the
U nn unit system of the unit.
tTurn off the power once and then
turn it on. The unit may operate
correctly. However, if the message
still remains on the LCD, turn off
the power immediately and contact
your Sony dealer.
DICOM TROUBLE Trouble has occurred in the DICOM
part of the unit.
tTurn off the power immediately and
contact your Sony dealer.
TAG INVALID Trouble has occurred in the IC tag part.
tTurn off the power immediately and
contact your Sony dealer.