Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Solar Powered
Motion Sensor Light
Model 7143
*Illustrations may vary from actual unit.
FEATURES
• LED solar powered light.
• Light operates automatically at night only.
• No wiring required.
• Wall mount only.
INITIAL BATTERY CHARGE
The solar panel requires full, direct sunlight to
charge the battery. Clouds, rain, snow, and other
weather conditions may not allow the solar panel to
completely recharge the battery. Other obstructions
such as buildings or trees may block the sun as well.
When installing the solar panel, make sure it is
aimed as described below with a minimum amount
of obstructions. If possible, mount the panel facing
toward the southern sky.
• PRIOR TO USE, the battery will require 3 to 7 days
of full sun to completely charge with the ON-OFF
switch in the OFF position. Plug the solar panel cable
into the connector extending from the bottom of the
battery case. If possible, aim the solar panel toward the
south and tilt it approximately 50° from horizontal (see
illustration on next page). If the solar panel cannot be
aimed toward the south, then tilt the panel approximately
30° if possible.
• Actual operating time will vary depending upon how
frequently the light is turned on by the motion sensor
and amount of sunlight collected.
• Solar lighting is not designed to equal standard 120V
lighting. The amount of light output is reduced to allow
the sun time to fully recharge the battery between
lighting cycles.
© 2014 HeathCo LLC
UNPACKING
Be sure to remove all contents from packaging and verify
all items are present before assembling this light fixture.
This package includes the following items:
Mounting
Screws
and Wall
Anchors
ON/OFF
Switch
Solar Light Fixture
WHERE TO MOUNT YOUR SOLAR
POWERED MOTION SENSOR LIGHT
The most important thing to remember for the operation
of your solar powered motion sensing light is that it works
from the power received from direct sunlight. The more
direct sunlight the solar panel receives in a day, the longer
the light will operate.
Solar Light Fixture:
The main unit contains the LEDs, motion sensor, and
battery. When deciding where to mount this unit, keep
in mind that the motion sensor that activates the light
has a "field of vision" of 30 feet (9 meters) in front of the
light and about 110° detection angle at a surrounding air
temperature of 77° F (25 °C).
Solar Panel:
The solar panel converts the sun's energy into electricity,
thus charging the battery stored in the solar light fixture.
The solar panel requires direct sunlight falling onto the
face of the solar panel for as long as possible over the
course of the day.
When choosing the location for the solar panel, make
sure it is aimed toward the south and is tilted to a suit-
able angle to allow as much direct sunlight to fall upon
it as possible. Make sure there is a minimum amount of
obstructions between the solar panel and the sun.
Also, make sure your solar panel location is not too far
away from the solar light fixture for the wires to reach
and connect.
Light
Solar Panel
Sensor
207197-02A

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Heath Zenith 7143

  • Página 1 Be sure to remove all contents from packaging and verify all items are present before assembling this light fixture. This package includes the following items: Solar Powered Light Solar Panel Motion Sensor Light Model 7143 Mounting Screws and Wall Anchors *Illustrations may vary from actual unit. ON/OFF...
  • Página 2 INSTALLATION Mounting the Solar Panel: 1. Using a 3/16" drill bit, drill pilot holes for the wall anchors Mounting the Solar Light Fixture: and insert three wall anchors. Mount the solar panel For best performance, mount the solar light fixture about 6 using four screws.
  • Página 3 3. Carefully route the solar panel cable to the light fixture. Adjusting Motion Sensor: Plug the solar panel cable into the connector extending After the initial 3-to-7-day charge, press the ON/OFF from the side of the battery case. switch to the ON position. IMPORTANT: Press the ON/OFF switch to the OFF On the bottom of the motion sensor there are two adjust- position and allow the battery to charge with 3 to...
  • Página 4: Things To Remember

    THINGS TO REMEMBER Adjusting Lamp Housing: Aim the lamp to face the area you wish to illuminate. • Periodically clean the solar panel with a soft cloth and Walking Test: warm water. Do not hose spray. Keep the panel clear of snow and leaves.
  • Página 5: Troubleshooting Guide

    TROUBLESHOOTING GUIDE SYMPTOM POSSIBLE CAUSE SOLUTION Lights does not activate in 1. ON/OFF switch is in OFF position. 1. Turn ON/OFF switch to the ON position. normal operation. 2. Lux control is set wrong. 2. Adjust Lux control toward ( 3.
  • Página 6: Luz Detectora De Movimiento Con Alimentación Solar

    Este paquete incluye Luz detectora de los siguientes elementos: Bombilla Panel Solar movimiento con alimentación solar Tornillos de Modelo 7143 montaje y anclas de pared Interruptor *Las ilustraciones pueden variar de la unidad real. ON/OFF Aparato de CARACTERÍSTICAS...
  • Página 7: Instalación

    INSTALACIÓN Montaje del panel solar: 1. Con una broca de 3/16 de pulgada, perfore agujeros Montaje de la lámpara solar: pilotos para los anclajes de la pared e inserte tres Para un mejor desempeño, instale la lámpara solar más anclajes de pared. Instale el panel solar con cuatro o menos a 6 pies (1,8 m) por encima del suelo.
  • Página 8: Regulación Final Y Arranque

    3. Guíe con cuidado el cable del panel solar hacia la lám- Regulación del detector de movimiento: para. Conecte el cable del panel solar en el conector Después de la carga inicial de 3 a 7 días, presione el que se extiende desde el lado de la caja de la pila. interruptor ON / OFF a la posición ON.
  • Página 9: Puntos Que Se Deben Recordar

    PUNTOS QUE SE DEBEN Regulación de la carcasa de la lámpara: Apunte la lámpara al área que desea iluminar. RECORDAR Prueba caminando: • Limpie el panel solar periódicamente con un trapo suave El detector detecta “movimiento” por el movimiento del y con agua tibia.
  • Página 10: Guía De Análisis De Averías

    GUÍA DE ANÁLISIS DE AVERÍAS SÍNTOMA POSIBLE CAUSA SOLUCIÓN Las luces no se activan en 1. El interruptor ON/OFF está en la posición 1. Gire el interruptor ON/OFF a la posición ON. operación normal. OFF. 2. Regule el control LUX hacia ( 2.
  • Página 11 L’emballage contient les éléments suivants : Éclairage à détecteur D’éclairage Panneau solaire de mouvements, à énergie solaire Vis de montage et dispositifs Modèle 7143 d’ancrage au mur Interrupteur *L’unité peut différer des illustrations. MARCHE/ ARRÊT Luminaire à énergie solaire CARACTÉRISTIQUES...
  • Página 12 INSTALLATION Montage du panneau solaire : 1. Au moyen d'une mèche 3/16 po, percez des trous Montage de l’appareil d’éclairage solaire : pour les ancrages muraux, puis insérez trois ancrages Pour la meilleure performance possible, monter l’appareil muraux. Installez le panneau solaire au moyen de d’éclairage solaire à...
  • Página 13 3. Acheminer soigneusement le câble du panneau Détecteur de mouvement réglable : solaire à l’appareil d’éclairage. Branchez le câble du Après la charge initiale de 3 à 7 jours, placez l'interrupteur panneau solaire dans la prise du câble qui sort du en position ON (MARCHE).
  • Página 14 RAPPEL Ajustement du socle de la lampe : • Nettoyer périodiquement le panneau solaire au moyen Orienter la lampe face au périmètre que vous désirez d’un chiffon doux et d’eau chaude. Ne pas l’arroser illuminer. directement au moyen du boyau. S’assurer que le Test de marche : panneau n’est pas couvert de feuilles ou de neige.
  • Página 15: Guide De Dépannage

    GUIDE DE DÉPANNAGE SYMPTÔME CAUSE POSSIBLE SOLUTION Les lumières ne sont 1. L’interrupteur MARCHE/ARRÊT est à la 1. Tourner l’interrupteur MARCHE/ARRÊT à la position pas activées en fonc- position ARRÊT. MARCHE. tionnement normal. 2. La commande Lux est mal réglée. 2.
  • Página 16 Purchase Information Información de la compra Renseignements d’achat Model #: _________________ Date of Purchase: _____________ Nº de modelo / N° de modèle Fecha de compra / Date d’achat Staple Purchase Receipt Here Engrape aquí el recibo de compra Agrafez le reçu d’achat ici PLEASE KEEP YOUR DATED SALES RECEIPT, IT IS REQUIRED FOR ALL WARRANTY REQUESTS.

Tabla de contenido