Transport And Storage; Maintenance; Warranty; Return Of Goods - VALPES LT 25 Manual De Instalación Y Funcionamiento

EN
INTRODUCTION
This manual has been made to guide you through the installation and use of our electric actuators for low temperatures.
Please, read it carefully before using our products and be sure to keep it.
DESCRIPTION
These electric actuators have been designed to perform the control of a valve with 90° rotation (or 180° in case of 3-position
version). We cannot be held responsible if the mentioned actuators are used in contradiction to this advice. Please consult us
for any different application.

TRANSPORT AND STORAGE


The forwarding agents being held as responsible for damages and delays of the delivered goods, the consignees are
obliged to express if applicable their reserves, prior to accept the goods. The goods delivered directly ex works are subject
to the same conditions.

The transport to the place of destination is carried out by using rigid packing material.

The products must be stored in clean, dry, and ventilated places preferably on appropriate palettes or shelves.

MAINTENANCE


Maintenance is ensured by our factory. If the supplied unit does not work, please check the wiring according to the electric
diagram as well as the power supply of the concerned electric actuator.

For any question, please contact our after-sales service.

To clean the outside of the actuator, use a lint and soapy water. DO NOT USE CLEANING PRODUCT WITH SOLVENT OR
ALCOHOL

WARRANTY


100% of the actuators are fully tested and set in the factory.

These products are 3-year warranty from the delivery date or 50,000 actuations against all types of manufacturing and
material faults (operating time and model class according to standard CEI34).

This guarantee will only be valid if the unit has not been disassembled or self-repaired during its service life. It does not
cover any wear and damage caused by shocks or faulty operation neither by the use of the unit under conditions not in
accordance with its nominal characteristics. The guarantee is strictly limited to the replacement of original parts found de-
fective on checking by our service personnel. The cost of shipping to our premises, the return of devices to the customer
as well as the repair cost will be chargeable. We will not assume the responsibility for any direct or indirect accidents/risks
originated by a failure of our products. The guarantee does not cover the consequences of breakdown and excludes any
payments for indemnities. The accessories and adaptations are excluded from the guarantee. In the case where a custom-
er has not proceeded to payments within the agreed period, our guarantee will be suspended until the delayed payments
have been received and with the consequence that this suspension will not prolong the guarantee period in any case.

RETURN OF GOODS


The customer is obliged to check the conformity of the goods with regard to their definition at the time of delivery.

The acceptance of the goods by the purchaser disclaims the supplier of all responsibility if the purchaser discovers any non
-conformity after the date of acceptance. In such case, the repair cost will be borne by the purchaser who will also exclu-
sively bear all financial consequences of any resulting damage. Returned goods will only be accepted if our prior agreement
has been given to this procedure : the goods must be sent free of all cost and being shipped solely and in their original
packing. The returned goods will be credited to the purchaser with a reduction of 40% on the unit's price charged in ac-
cordance with the original invoice of the returned goods.

SAFETY INSTRUCTIONS


The electric power supply must be switched-off before any intervention on the electric actuator (i.e. prior demounting its
cover or manipulating the manual override knob).

Any intervention must only be carried out by a qualified electrician or other person instructed in accordance with the regula-
tions of electric engineering, safety, and all other applicable directives.

Strictly observe the wiring and set-up instructions as described in the manual: otherwise, the proper working of the actua-
tor can not be guaranteed anymore. Verify that the indications given on the identification label of the actuator fully corre-
spond to the characteristics of the electric supply.
 Respect all safety rules during fitting, dismantling and porting of this apparatus

Lifting and carrying through strapping the hand wheel is not allowed.

Do not mount the actuator « upside down ». Risk: declutching mechanism failure

Do not mount the actuator less than 30 cm of a electromagnetic disturbances source.

Do not position the equipment so that it is difficult to operate the disconnecting device.
DSBA3700 • Rév. 01/10/2020
To be read prior to the installation of the product
.
19