GLOBBER TRIKE 4IN1 Manual De Instrucciones página 8

Please carefully read the instructions before assembling and using the
product. Keep the instructions for future reference.
Be careful when unpacking and assembling the product.
This product must be assembled by a responsible adult.
Remove all the parts which are not necessary for play before giving the
product to your child.
Warning! Secure the child in the harness at all times.
Warning! Do not step or stand on back of frame which will cause product
overturned.
Tricycle mode: Warning! Not to be used by children over 36 months;
insufficient strength to support.
HOW TO ASSEMBLE EXPLORER TRIKE 4in1
1. The front wheel's fork needs to be aligned with the frame of the trike;
then insert the stem of the front wheel's fork into the frame.
2. Take the handlebars and align them with the front wheel by making
sure the stem of the front wheel's fork slots into the handlebars'
column. Make sure the handlebars are placed in the correct direction
with the top column facing outwards, away from the seat. Push the
handlebars down until you hear a click to securely fix them in place.
3. Turn the pedal locks of the front wheel in the direction of the unlocked
symbol; place the pedals in the front wheel's slots. Turn the pedal
lock in the direction of the locked symbol to secure the pedals in the
front wheel. You may need to hold the opposite pedal lock to ensure
that the pedal doesn't spin freely.
4. To install the rear wheels, you need to unscrew the knob at the end of
the wheel assembly. The brakes of the rear wheels must be pointing
inward when they are installed for all trike stages. Place the wheel in
the hexagonal slot at the rear of the trike frame and ensure that the
brake is upwards and doesn't touch the ground. Once the wheel is
in the correct position, you need to re-screw the knob back into the
wheel slot to ensure the wheel will remain securely in place.
5. To insert the saddle, you must first open the clamp and press the
bottom spring-loaded button on the saddle stem. Then, push the
saddle down until you hear a click. Close the clamp. The saddle
is adjustable with 2 available heights (31cm; 34cm). The minimum
insertion depth is where "MAX" is marked on the stem when placing
8
the top spring-loaded button in the saddle's stem hole. This is the
highest height of the saddle. The maximum insertion of the saddle is
pushing the saddle down until the saddle's stem is all the way down.
This is the lowest height of the saddle.
6. Take the footrest and slide it up the saddle stem. You must press the
spring-loaded button at the bottom of the saddle stem; the footrest is
secure once you hear a click and twist the knob under the footrest to
90 degrees. The footrest must be facing forwards, not backwards, to
be in the correct position.
Warning! Check footrest is securely locked before every use.
7. To assemble the parent handlebar, take the top part of the parent
handle, where there is the black handle, and place it into the bottom
shaft by pressing the spring-loaded button. There are 2 available
heights on the parent handlebar (92cm; 96.5cm). Make sure to
align the spring-loaded button with the holes; you must hear a click
to ensure the handle is securely in place. To secure the parent
handlebar to the trike, carefully place the shaft through the saddle's
hole and into the hole on the trike's frame. Once you hear a click, the
pole is secure.
To remove the parent handle, you must press the red button under
the trike's frame; then release the shaft and carefully lift the parent
handle out.
8. Assemble the safety bar by first unscrewing the top cap of the middle
safety bar. Next, put one side of the safety bar on top of the middle
safety bar, followed by the other side. Screw the cap on top of the
middle safety bar to secure the right and left safety bars. Correct
assembly of the safety bar will show both safety bar sides at the
same height.
9. Put the seat on top of the saddle; make sure the knob on the seat is
aligned with the saddle slot, so it can slide through the saddle slot.
To secure the seat to the saddle, turn the knob under the seat 90
degrees. Insert the middle safety bar in the hole at the front of the
seat; press the red button on the side of the middle safety bar and
push until the red button is hidden in the seat. Slide the sides of the
safety bar into the gaps on the side of the seat.
Warning! Check seat and safety bar are securely locked before
every use.