Manual Ignition; Switching Off; Setting The Clock - EdilKamin IRIS UP Instalación Uso Y Mantenimiento

Manual ignition

At temperatures of less than 3°C (too low for the heating element to glow) or if the heating element is temporarily out of order,
a firelighter may be used for ignition. put a piece of well lit firelighter in the combustion chamber, close the door and press ON/
OFF.
Operating modes
(when the stove is working, press the A/m key to switch between modes)
Manual: adjust the working power (from P1 to P3 with the left knob) and the ventilation (with the right knob)
Automatic: set the temperature which the room is to reach; the stove automatically adjusts the working power to reach it (P3) or
maintain it (P1).
If you set a lower temperature than current room temperature, the stove operates at P1 and consumes the corresponding quantity
of pellets.
Note on flame variability
Any variations in the state of the flame depend on the type of pellet used, the normal variability associated with solid fuels and the
periodic automatic combustion chamber cleaning (which does NOT replace the essential cold vacuum cleaning by the user before
ignition).

Switching off

Hold the ON/OFF key down for two seconds while the stove is operating. The shutdown procedure starts and the word "Off"
appears on the display (for a total of 10 minutes).
During shutdown:
• Pellet loading ceases.
• Ventilation turns up to maximum.
• The smoke expulsion motor turns up to maximum.
Never unplug the stove while it is shutting down
WEEKLY TIME PROGRAMMER BUILT INTO PANEL
The concept of the weekly time programmer built into the central panel
It is possible to set 3 ignition programmes
Pr01 with settable on and off times
Pr02 with settable on and off times
Pr03 with settable on and off times
It is possible to enable one or more of the three programmes on each day of the week (day1 = Monday, day2 = Tuesday...day7 =
Sunday).
When on standby, the display alternates between showing the ignition mode (P1, P2, P3 or a temperature) and the clock.
Refer to page 20 for each of the buttons to press.

Setting the clock

Press the "hourglass" once. When ESC appears, press On/off(-). When SET appears, press the "hourglass" again.
HOUR:MIN appears. It is now possible to change the setting with the On/off (-) and Am (+) keys. Once the time is set,
press the "hourglass" to confirm. The day number then appears (day1 = Monday, day2 = Tuesday...day7 = Sunday). It
is now possible to change the day with the On/off (-)and Am (+) keys. Press the "hourglass" to confirm. When ESC
appears, press the "hourglass" again to quit programming.
Enabling programmes
Press the "hourglass" once. When ESC appears, press Am(+). When Pr off appears, press the "hourglass" again. When
"off" appears, press On/off(-) or Am(+) to change it to "on". Press the "hourglass" to confirm. When ESC appears, press the
"hourglass" again to quit programming. When the stove is in Pr mode, it responds to programmed on and off times.
Setting a programme (e.g. Pr01)
Press the "hourglass" once. When ESC appears, press Am(+) repeatedly until Pr01 appears (after Pr On, set as
described above).
Confirm with the "hourglass". ON P1 appears followed by the programme 1 ignition time.
This time can be changed using the On/off(-) and Am(+) keys.
Confirm by pressing the "hourglass".
OfP1 appears, followed by the programme 1 off time. This time can be changed using the On/off(-) and Am(+) keys.
Confirm by pressing the "hourglass".
Ofd1 appears (i.e. programme 1 is not enabled for day 1, Monday). To enable it, press Am(+). Ond1 appears, i.e.
programme 1 is enabled on Monday.
Press the "hourglass" to move on to the second day, and so on until day7.
Press the "hourglass" to quit.
The Pr 02 and Pr 03 on and off times and the days on which they are enabled can be set in a similar way.
When the programmes are enabled, a green light appears next to the hourglass symbol.
- 21
-