Rules For Safe Operation - Ryobi CLT1830B Manual De Utilización

GB GB
F F D D E E

RULES FOR SAFE OPERATION

WARNING
The tools should be operated with the ONE+
battery pack.
When using battery operated tools basic safety
precaution should always be followed to reduce
the risk of fire, leaking batteries and personal
injury, including the following.
Read the operation manual and follow all
warnings and safety instructions.
Wear eye protection and ear protection.
Do not use this machine in wet weather
conditions!
Wear protective clothing and boots.
Wear non-slip, heavy duty gloves.
Keep all bystanders at least 15 m away.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING:
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future
Q
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
Q
areas invite accidents.
Do not operate power tools in explosive atmospheres,
Q
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite
the dust or fumes.
Keep children and bystanders away while operating
Q
a power tool. Distractions can cause you to lose
control.
I I P P NL NL S S DK DK N N FIN GR HU FIN GR HU CZ RU CZ RU
English
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
Q
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric
shock.
Avoid body contact with earthed or grounded
Q
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Q
Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord for
Q
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
If operating a power tool in a damp location is
Q
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
When operating a power tool outdoors, use an
Q
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
NOTE: The term "residual current device (RCD)" may
be replaced by the term "ground fault circuit interrupter
(GFCI)" or "earth leakage circuit breaker (ELCB)".
PERSONAL SAFETY
Stay alert, watch what you are doing and use
Q
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result
in serious personal injury.
Use personal protective equipment. Always wear eye
Q
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the switch is
Q
in the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energizing power tools that have the switch on invites
accidents.
Remove any adjusting key or wrench before turning
Q
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance at
Q
all times. This enables better control of the power tool
10
RO PL SLO HR TR EST LT RO PL SLO HR TR EST LT LV LV SK BG SK BG