Ryobi CLT1830B Manual De Utilización página 21

GB
F D E I
DO NOT place charger in an area of extreme heat
Q
or cold. It will work best at normal room temperature.
IMPORTANT INFORMATION FOR RECHARGING
HOT BATTERY PACK
W h e n u s i n g y o u r l i n e t r i m m e r c o n t i n u o u s l y,
the batteries in your battery pack will become hot.
You should let a hot battery pack cool down for
approximately 30 minutes before attempting to recharge.
NOTE: This situation only occurs when continuous use
of your line trimmer causes the batteries to become hot.
It does not occur under normal circumstances. If battery
pack is below normal temperature range, the green LED
on charger will come on. Allow battery pack to reach
normal temperature, then the red LED will come on.
INSTALL BATTERY PACK
Place the battery pack in the string trimmer.
Q
Align raised rib on battery pack with groove in string
trimmer. See Figure 7.
Make sure the latches on the battery pack snap
Q
in place and that battery pack is secured in string
trimmer before beginning operation.
REMOVE BATTERY PACK
Locate latches of battery pack and depress both sides
Q
to release the battery pack from the string trimmer.
See Figure 7.
Remove battery pack from the string trimmer.
Q
CAUTION
When placing battery pack in your string trimmer,
be sure raised rib on battery pack aligns with
groove in string trimmer and latches snap in
place properly. Improper assembly of battery
pack can cause damage to internal components.
REMOVING ADDITIONAL SPOOL FROM
SPOOL HOLDER
Turn the spool in the spool holder (Fig. 1 - B)
counterclockwise and pull the additional spool out of the
holder
ADDING ADDITIONAL SPOOL TO SPOOL HOLDER
Push the spool into the spool holder (Fig. 1 - B) and turn
clockwise until the spool clicks into a safe position
STARTING THE STRING TRIMMER
Press and hold the trigger lock button. See Figure 8.
Q
This makes the trigger operational.
Release the trigger lock button and continue to
Q
squeeze the trigger for extended operation.
P NL S DK N FIN GR HU CZ RU RO PL SLO HR TR EST LT
English
STOPPING THE STRING TRIMMER
Release the trigger to stop the string trimmer.
Q
Upon release of the trigger, the trigger lock button will
Q
be automatically reset to the lock position.
HOLDING THE STRING TRIMMER
WARNING
Dress properly to reduce the risk of injury when
operating this unit. Do not wear loose clothing or
jewellery. Wear eye protection. Wear heavy, long
pants, boots and well fitting gloves. Do not wear
short pants, sandals or go barefoot.
Hold the string trimmer as shown. See Figure 9.
Q
Right arm is slightly bent, the right hand holding the
rear handle. Left arm is straight, the left hand holding
the front handle. The unit should be slightly below
waist level.
The string head on your string trimmer should be
Q
parallel to the ground and should easily contact the
material being cut without the operator having to
bend over. A simple shaft adjustment accommodates
most user's heights.
USING THE STRING TRIMMER
ADVANCING LINE
Your string trimmer is equipped with a string head,
which allows the operator to release more cutting line
without stopping the motor. As the line becomes worn or
frayed, additional line can be released by lightly tapping
the string head on the ground while operating the string
trimmer at full throttle. See Figure 10. For best results,
tap the head on bare ground or hard soil. If line release is
attempted in tall grass, the motor may overheat.
Approximately 25.4 mm (1 inch) of cutting line is released
each time the head is tapped on the ground.
Always keep the cutting line fully extended. If the string is
worn too short you may not be able to advance the string
by tapping the head on the ground. If this occurs, stop
the motor, remove the spool as described in the following
section, feed the cutting line through the opening in spool
housing and reassemble the spool to the string head.
CUTTING LINE
This string trimmer is equipped with a string cut off blade
on the grass shield. See Figure 11. For best cutting,
advance line until it is trimmed to length by the string
cut-off blade. Advance line whenever you hear the
motor running faster than normal. This will maintain best
performance and keep the cutting line long enough to
advance properly.
15
LV SK BG