TSQW1CO
167392
Analogue time switch 7 d
Analog-Zeitschaltuhr 7 d
Minuterie analogique 7 d
Interruttore orario analogico 7 d
Interruptor horario analógico 7 d
Interruptor horário analógico 7 d
Analoge schakelklok 7 d
Analogowy zegar sterujący 7 d
GB
D
F
I
E
P
NL PL
ENGLISH
Basic safety instructions
WARNING
Danger of death through electric
shock or fire!
Installation should only be carried out
by a qualified electrician!
Designated use
• The time switch can be used for lighting,
ventilation, fountains, advertising hoardings etc.
• Only for use in closed, dry rooms
• Installation on DIN top hat rail (in accordance
with DIN EN 60715)
Disposal
Dispose of device in environmentally sound
manner
Description
Connection/installation
WARNING
Warning, danger of death through electric
shock!
Must be installed by qualified electrician!
Disconnect power source!
Cover or shield any adjacent live components.
Ensure device cannot be switched on!
Check power supply is connected!
Earth and bypass!
Quarz movement only starts in a few minutes
after power is switched on.
Full power reserve is achieved after approx.
5 days.
TSQW1CO
1910822
R200h (230V)
R100h (110V)
16(4) 250
~
1
2
3
TSQW1CO
Set day of the week
day (3 = wednesday)
Switching pre-selection/manual
setting
Program timing disc
Switching segments
(1 = 2 h)
Morning/afternoon
(AM/PM) time display
Hand for setting time (hours and
minutes) can be adjusted anti-
clockwise and clockwise; turn
minute hand firmly to left
Three way switch:
Permanent ON – AUTO –
Permanent OFF
Klick
45°
45°
110–230V~
–20T
50–60Hz
N
L1
L1/L2/L3
Set time
e.g. 3:00 (morning)
e.g. 15:00 (afternoon)
Set manual operation/
switching pre-selection
in advance 3:00 ON (= 1)
n
The time switch operates the set swit-
ching times, i.e. it returns to program.
Connection, technical data see on the back side
Technical Data
TSQW1CO
Operating voltage:
110–230 V~, 50–60 Hz
Power consumption:
max. 2,5 VA
Switching contact:
potenzialfrei (not for SELV/PELV)
Contact:
two-way switch
Gap:
<3 mm (µ)
Contact material:
Ag
Switching capacity:
16 A, 250 V~, cos ϕ = 1
4 A, 250 V~, cos ϕ = 0,6
Incandescent lamp load: 1100 W
Fluorescent lamp load: parallel-corrected 2 x 40 W (4,7µF)
Perm. ambient temperature: –20 °C ... +55 °C
Protection class:
II in accordance with EN 60730-1 for designated installation
Protection rating:
IP 20 in accordance with EN 60529
Time accuracy:
≤ ±1 s/s day at +20 °C
Power reserve:
R 200 h (230 V), R 100 h (110 V)
Pollution degree:
2
Type:
1 BSTU
Service address/Hotline
Eaton Industries (Austria) GmbH
Scheydgasse 42
A-1215 Wien
www.eaton.com
Set switching times
e.g. mon–fr 10:00–20:00 ON
Set 1 –
– 0 permanent
n
switching
1
Program is not operated.
1 = Permanent ON
0 = Permanent OFF
309518