Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Tool
5/32" Hex Key Wrench
Part No. 401331
405659-1
1/07
30 ° Cordless Framing Nailer
Cleaning Procedure
This procedure provides a simple but effective way to
clean your Paslode Cordless Framing Nailer and
maintain reliable operation. Regular cleaning and
lubrication will also extend part life and provide
maximum nail driving power.
Only one tool is necessary to disassemble the Paslode
Cordless Framing Nailer in preparation for cleaning:
the 5/32" hex key wrench provided with the Paslode
Cordless Framing Nailer.
Paslode recommends that an aerosol "Degreaser
Cleaner," such as Paslode
No. 219086), be used for cleaning. This cleaner is
available through your local Paslode Dealer.
If a different type of degreaser cleaner is selected,
make sure that it will not damage rubber. Both of the
O-Ring seals in the area that will be cleaned are made
of a rubber compound. Chemical damage to these O-
Ring seals may result in the tool being made
inoperable.
Although "safety" cleaners generally provide reduced
risk of fire and are more stable than other cleaners,
they cannot be handled carelessly. Always follow the
manufacturer's instructions and never spray cleaner on
the Paslode Cordless Framing Nailer, unless the tool
has been allowed to cool down.
To begin, you will need the following items:
Degreaser Cleaner
Part No. 219086
®
Degreaser Cleaner (Part
Paslode Cordless Lubricating Oil
Part No. 401482
1
Publicidad
Tabla de contenido
Manuales relacionados para Paslode 30
Resumen de contenidos para Paslode 30
- Página 1 Regular cleaning and lubrication will also extend part life and provide maximum nail driving power. Only one tool is necessary to disassemble the Paslode Cordless Framing Nailer in preparation for cleaning: the 5/32" hex key wrench provided with the Paslode Cordless Framing Nailer.
- Página 2 Remove the cap and air filter by unscrewing the four #10-24 Socket Head Cap Screws. DANGER Never operate the Paslode Cordless Framing nailer unless all four Socket Head Cap Screws are firmly tightened on the cylinder head. Failure to do this could result in tool damage, fire and personal injury.
-
Página 3: Cylinder Head
Cylinder Head Step 1 Grasp the Cylinder Head O-Ring with the thumb and index finger of one hand, and pull the O-Ring out of the groove slightly by applying light pressure while pulling. Step 2 Grasp the protruding portion of the O-Ring with the other hand, and gently pull the O-Ring out of the groove and over the fan. - Página 4 Set the Handle/Cylinder Head Assembly aside. Note: Paslode Cordless Lubricating Oil is specially formulated for use in the Paslode Cordless Framing Nailer. The use of other types of lubricants may cause rapid build-up of combustion residue or result in premature part failure.
-
Página 5: Motor Assembly
Motor Assembly Step 1 Push the Piston Assembly to the "down" position using the handle portion of the screwdriver or a clean piece of wood. Step 2 Spray a liberal amount of degreaser cleaner into inside of Sleeve and Combustion Chamber. Invert Motor Assembly, and let excess cleaner and dirt drain out. - Página 6 Motor Assembly Step 4 With Motor Assembly tilted up, squeeze 4-5 drops of oil into Sleeve (Area "A") and 5-6 drops onto lower lip of Combustion Chamber (Area "B"). Rotate Motor Assembly while oiling to ensure oil is evenly distributed around Sleeve and lip. See Tool Cutaway Illustration, page 7.
- Página 7 Motor Assembly Step 7 Tilt the Motor Assembly upright, and apply 3-4 drops of Paslode Cordless Lubricating Oil evenly spaced around the top of the Combustion Chamber (Area "C"). Spread the oil using your fingertip. Step 8 Reassemble the Paslode Cordless Framing Nailer following disassembly Steps 1-3, page 2 in Reverse order.
- Página 8 Weekly extended periods, cleaning should be performed at shorter intervals. Every 2 Weeks Paslode has developed this chart as a guideline to ▲ Monthly assist you in establishing the proper cleaning schedule for the type of use the tool is getting. If you...
- Página 9 Allen (llave de cabeza hexagonal) de 5/32 plg. que se entrega junto con su clavadora Impulse ® Paslode recomienda que use un limpiador en aerosol, tal como el "limpiador de seguridad" Paslode (No. 219086). Este limpiador está disponible a través de su representante Paslode.
-
Página 10: Conjunto Del Mango Y El Mecanismo De Alimentacion
Conjunto del mango y el mecanismo de alimentacion PELIGRO Se deben guitar todos los sujetadores, el cartucho de gas y ta batería antes de reparar la herramienta. Paso 1 Usando la llave Allen de 5/32 plg. (#401331) quite el conjunto del mango y el mecanismo de alimentacion: destornille los dos tornillos de casquete de boca tubular #10-24 x 1-1/8 plg. -
Página 11: Tapa Del Cilindro
Tapa del cilindro Paso 1 Tome el "O-Ring" de la tapa del cilindro con los dedos pulgar e indice de una mano y saque el " O- Ring" de la ranura aplicando una ligera persión al tirar de él. Paso 2 Tome la parte que sobrsale del "O-Ring"... - Página 12 Coloque el conjunto de la tapa del cilindro y el mango a un lado. Nota: El aceite lubricante Paslode Cordless está especialmente formulado para usarse con la clavadora. El uso de otros tipos de lubricantes puede causar una acumulación rápida de residuos de la combustión o la descompostura...
-
Página 13: Conjunto Del Motor
Conjunto del motor Paso 1 Oprima el conjunto del pistón hasta la posición abajo con el mango de un martillo o con un pedazo limpio de madera. Paso 2 Aplique una buena cantidad de limpiador de seguridada dentro de la manga y de la cámara de combustión. - Página 14 Conjunto del motor Paso 4 Con el conjunto del motor hacia arriba, ponga entre 4y 5 gotas de aceite lubricante en la manga (Area "A") y des 5 a 6 gotas en el labio inferior de la cámara de combustión (Area "B"). Gire el conjunto del motor mientras aplica las gotas de aceite para asegurarse de que el aceite se distribuye por la camisa y el labio.
- Página 15 Conjunto del motor Paso 7 Incline el conjunto del motor y aplique entre 3 y 4 gotas de aceite lubricante Paslode Cordless uniformemente alrededor de la parte superior de la camara de combustión (area "C"). Disperse el aceite con el dedo.
-
Página 16: Clavadora Paslode 30 ° Cordless Procedimiento De Limpieza
★ 2-3 Dias en un ambiente sucio o durante largos períodos, debe limpiarla a intervalos más cortos. Semanalmente Paslode desarrolló esta tabla como una guía para Cada 2 Semenas ayudarlo a establecer el programa de limpieze ▲ Mensualmente apropiado según el uso que le dé a la herramienta.