Tabla de contenido
Publicidad
Enlaces rápidos
Publicidad
Tabla de contenido
Manuales relacionados para Paslode T200-F18P
Resumen de contenidos para Paslode T200-F18P
- Página 1 Part# 515600 MODEL T200-F18P 18 Ga. Brad Nailer IMPORTANT! OPERATING MANUAL AND DO NOT DESTROY SCHEMATIC It is the customerʼs responsibility to have all operators and service personnel read and understand this manual. PRINTED IN U.S.A. © 2017, Illinois Tool Works Inc.
- Página 2 INTRODUCTION The PASLODE T200-F18P Brad Nailer is a quality-built tool designed for use in residential ® trim applications. This tool will deliver efficient, dependable performance when used according to the manufactures guidelines. Please study this manual including the safety instructions to fully understand the operation of this tool.
-
Página 3: Tool And Fastener Specifications
TOOL AND FASTENER SPECIFICATIONS MODEL NO. T200-F18P (Part # 515600) HEIGHT 10.63" WIDTH 2.56" LENGTH 10.04" WEIGHT 2.9lbs. NAIL LENGTH - " " 2 SHANK DIAMETER 18 gauge OPERATING PRESSURE 80 to 120 psi TOOL AIR FITTINGS This tool uses a 1/4” N.P.T. male plug. The inside diameter should be .28” (7mm) or larger. -
Página 4: Safety Instructions
CONTACTING ELEMENT Use only parts and fasteners specifically designed and This tool is equipped with a safety mechanism, called a recommended by Paslode for use in the tool and for ® a work contacting element, to help prevent accidental work to be done. Using unauthorized parts and fasteners firing. - Página 5 INSTRUCTIONS FOR LOADING Step No. 1 – Disconnect the tool from its air source.Grasp the finish nailer firmly with one hand and press the orange magazine release button at the rear of the handle and slide the magazine cover back towards you. Disconnect air Press release.
-
Página 6: Tool Operation
Use only fasteners that meet Paslode specifications. ® fastener. Use of fasteners that do not meet Paslode specifica- ® tions can result in damage to the tool or injury to the Keep the trigger depressed and continue to bounce the ■... -
Página 7: Cold Weather Care
Reduce the regulated air pressure to 30 psi. Use only Paslode approved fasteners in the tool, and ensure that they are correct for the application. Remove all fasteners from the tool. Ensure that a male air fitting is securely connected to Collect an air line and blank fire the tool. -
Página 8: Clearing A Jam
Operation Continued: Clearing a Jam Changing the work contact element. Disconnect tool from its air source. Disconnect tool from its air source. Remove all fasteners. Unlatch the front guide and lift open. Reversable belt hook Remove jammed fastener and relatch front guide. -
Página 9: Operator Troubleshooting
Tool skips during operation - no fasteners are driven Check magazine for proper fasteners. Magazine from time to time. follower should slide freely. Clean as needed to remove debris. Make sure correct fasteners are being used. ® Use fasteners that meet Paslode specifications only. - Página 10 PARTS LEGEND T200-F18P 515600 576921 Driver Guide 617539 Screw 617513 Screw 617558 Bushing 576922 Screw 617504 Air Deflector 576923 Plate 576913 Spring 576966 Spring Washer Screw 617533 576924 Screw 617535 Washer 617547 Washer 617489 576925 617550 Gasket, Cap Front Plate...
- Página 11 T200-F18P BRAD NAILER 515600 55 56 57...
- Página 12 ACCESSORIES ubricants f t i Tool Cleaner l l a . s l Safety Glasses Tool Case Handy carrying case that conveniently stores 515615 your tool Tool Case Latch 617559 Work Contact Element 576928 576935 Contact Trigger (Orange) 576917 An Illinois Tool Works Company 155 Harlem Avenue Glenview, IL 60025 ©...