Paslode 901000 Manual De Instrucciones
Ocultar thumbs Ver también para 901000:

Publicidad

Enlaces rápidos

IMPORANT!
R
DO NOT DESTROY
It is the customer's responsibility to have
all operators and service personnel read
and understand this manual.
Printed in U.S.A.
© 2010 Illinois Tool Works, Inc.
901070-8
03/10
Part No. 901000
OPERATING MANUAL
www.paslode.com
19

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Paslode 901000

  • Página 1 Part No. 901000 OPERATING MANUAL IMPORANT! DO NOT DESTROY It is the customer's responsibility to have all operators and service personnel read and understand this manual. Printed in U.S.A. © 2010 Illinois Tool Works, Inc. www.paslode.com 901070-8 03/10...
  • Página 3: Tabla De Contenido

    Contents Introduction and Warranty..........2 An Overview of Paslode Cordless 18 Gauge Brad Nailer ..................3 Safety Instructions ............4 Battery and Charger ............7 Fuel Cell and Metering Valve .......... 9 Preparing the Paslode Cordless 18 Gauge Brad Nailer for Use................12 Paslode Cordless 18 Gauge Brad Nailer Operation ..
  • Página 4: Introduction And Warranty

    ONE-YEAR LIMITED WARRANTY Paslode's sole liability hereunder will be to replace any part or accessory A one-year warranty will apply to all parts, except those listed which proves to be defective within the specific time period. Any replacement...
  • Página 5: An Overview Of Paslode Cordless 18 Gauge Brad Nailer

    An Overview of the Paslode Cordless 18 ga. Brad Nailer Specifications Description Weight- 4 lbs 14oz. Dimensions: with battery The Paslode Cordless 18 ga. Brad Nailer is a self-contained, Height 11-1/2 inches fully portable nailer that uses liquid hydrocarbon fuel to...
  • Página 6: Safety Instructions

    The following safety instructions have been included in this booklet to provide you with basic information necessary for WARNING safe operation of the Paslode Cordless 18 ga. Brad Nailer . DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY Do not expose the tool to PRECAUTIONS AND MANUAL INSTRUCTIONS.
  • Página 7 EAR safety gear when until it is completely against the work surface. working with or in the NEVER operate the tool if the work contacting element vicinity of the Paslode is not working properly. Cordless 18 ga. Brad Nailer. 8. ALWAYS...
  • Página 8 Battery Disposal: The Paslode batteries contain cadmium and must be recycled or disposed of properly. It is illegal in some areas to place a nickel-cadmium battery into the trash or solid waste stream. You may contact your local recycling center for information on where to return the spent battery or call 1-800-822-8837 for information on Ni-Cd battery recycling in your area.
  • Página 9: Charging Instructions

    Battery and Charging System Battery and Charging System Charging Instructions The Paslode Cordless tools come with a recharge- 1. Remove wall mount unit with the orange label from able battery and its own charging system. This the tool case and plug into a 120V AC outlet. Set...
  • Página 10: Battery And Charging System

    Battery and Charging System Battery Indicator Light On the right side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light. If the indicator light blinks red, recharge the battery.
  • Página 11: Fuel Cell And Metering Valve

    Never inhale the spray. NOTE: Altitude Restriction Keep out of the reach of children. Paslode Cordless technology is powered by an Store fuel cell(s) in well-ventilated areas only. internal combustion engine and are effected by altitude. The tool may lose power or not cycle consistently at elevations of 4000 feet or greater.
  • Página 12 Paslode Cordless Fuel Cell Disposal Guidelines Paslode the industry leader in cordless technology provides this information to assist users with the proper disposal of discarded fuel cells. Acceptable disposal options vary depending on the type of fuel cell users. All users must consider federal, state and local solid waste regulations to ensure that discarded fuel cells are disposed of properly.
  • Página 13 Fuel Cell and Metering Valve As you slide the metering valve/fuel cell assembly into the Inserting Fuel Cell Cordless Brad Nailer, you will notice a yellow adapter at the Inserting the metering valve/fuel cell assembly into the top of the cylinder pocket. As shown in the illustration, this Cordless Brad Nailer is very simple.
  • Página 14: Loading Fasteners

    18 gauge fasteners designed to be used with the tool. Use the Cordless Brad Nailer outdoors, in dry weather, The use of fasteners that do not meet Paslode standards when the nailer, fuel cell, and battery are between could cause tool damage and will void all warranty 20°F (-7°C) and 120°F (49°C).
  • Página 15: Paslode Cordless 18 Gauge Brad Nailer Operation

    Paslode Cordless 18 ga. Brad Nailer Operation Operation: PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. Fan motor starts, fuel is injected into combustion Turn chamber and adjustment mixed with air by wheel in the fan. either direction SQUEEZE...
  • Página 16: Fasteners And Applications

    Fasteners The Paslode Cordless 18 ga. Brad Nailer drives Paslode 18 Gauge Brad Nails. Fasteners are collated into strips of 50 for easy loading. Paslode fasteners are designed to be used in Paslode tools, use of other fasteners may cause damage to the tool or injury to the tool operator.
  • Página 17: Servicing

    Nailer, clearing a jammed fastener is easy: DANGER 1. Remove the battery. Never attempt any maintenance of a Paslode Cordless 2. Pull the latch, releasing front guide. Pivot front guide tool without first removing the fuel cell and battery. forward.
  • Página 18: Air Filter

    4. Check work contacting element to ensure it is operating freely. GRILLE Paslode Cordless Tool Accessories A variety of accessories are available for the Paslode Cordless 18 ga. Brad Nailer: FILTER No-Mar Replacement Tip -Hard Tip Part No. 901048 No-Mar Replacement Tip -Soft Tip Part No. 901067 Battery - Part No.
  • Página 19: Troubleshooting

    Spark wire out of spark plug. Remove cap and check spark lead, insert in spark plug and replace cover. Spark plug is dirty. Clean tool cylinder head. No spark is generated. Return tool to authorized Paslode dealer for ® service.
  • Página 20 Work-contacting element is bent, or is dirty. element. tool cycles. ® If tool will not operate after following the above service directions, return the tool to an authorized Paslode representative for service. For the nearest Paslode representative call 1-800-682-3428. ®...

Tabla de contenido