Publicidad
Idiomas disponibles
Idiomas disponibles
FEATURES
The KOBRA 260TS, 270TS, 310TS, is suitable for shredding
single, and computer printouts as well as CD-ROMS/DVDS and
CREDIT CARDS.
For specifications and cutting capacity,see table on page 22.
INSTALLATION
For machines with a removable plug, use an easily accessible
power socket near the machine.
- KOBRA 260TS Fig.1
Once the machine has been taken out of its packaging, position
the head of the machine (A) on the cabinet (B).Open the door (C)
and slide the bag frame (D) off its tracks (E).
Fit the plastic bag (F) which comes with the shredder to the bag
frame (D) then slide it back onto the track (E) in fully,position the
container for shredded CD/DVD/CREDIT CARD particles (12) on
the inside of the door and shut the door again (HS models are
not equipped with cutting blades for shredding CD/DVD/CREDIT
CARDS and a separate particle collection bin (12).
- KOBRA 270TS/KOBRA 310TS Fig.2
Once the machine has been taken out of its packaging,position
the head of the machine (G) on the cabinet (H).Open the door (I)
and remove the bag frame (M).
Fit the plastic bag (N) which comes with the shredder to the bag
frame (M) then slide it back onto the track (L).
Push the bag frame (L) in as far as it will go and close the door (I).
The KOBRA 270TS and 310TS (HS models axcluded) are
supplied with a canvas bag for the separate collection of
shredded CD/DVD/CREDIT CARD particles.
CONTROLS with TOUCH SCREEN tecnology.
❍
All shredders in the KOBRA 260TS, 270TS and 310TS range
come with TOUCH SCREEN tecnology.Machine functions
are activated by simply touching the respective button on the
control panel.
❍
FORWARD: Simply touch the FORWARD button and the
cutting blades operate in the forward direction.
Leave your finger on the button for 7 seconds
and the machine carries out a 30 second
shredding cycle making it possible to shred
t r a s p a r e n t m a t e r i a l w i t c h w o u l d n o t
automatically start the machine since it is
invisible to the electronic eyes.
❍
STOP:
Touch the STOP button and the machine stops
Instantly.
❍
REVERSE: Touch the REVERSE button and the cutting
blades go into reverse.
❍
OIL:
Touch the OIL button and the light (5) goes off
after manual lubrification.Or signals that oil is low
if the machine is equipped with the AUTOMATIC
OILER system.
USING THE MACHINE Fig.3
Once the machine has been plugged in to the mains, press the
ON/OFF button (O),the bar (P) on the control panel lights up and
machine is ready for use.If the machine is then not used for 8
seconds,the bar(P) goes off and the machine is put on stand-by
with zero power consumption and the ENERGY SMART light(1)
comes on.
As soon as any material to be shredded is introduced into the
throad,the machine comes on again automatically. If the
machine is not used for 4 hours,it switches off automatically from
the mains power supply and the ENERGY SMART light (1) goes
off.
To switch the machine back on press the ON/OFF button (O).
SHREDDING SINGLE SHEETS OF PAPER (FIG.3)
(A COMMON FUNCTION OF ALL THE
KOBRA 260TS/270TS AND 310TS).
When sheets of paper are inserted into the throat (2),the light bar
(P) comes on (if off) and the machine begins shredding
automatically thanks to two electronic eyes (3) located on the
inside of the throat which detect the throughput of sheets of
paper and automatically stop the cutting blades a few seconds
after shredding is finished.
The machine is fitted with a LOAD METER (4) which allows you to
monitor the load capacity of your machine.
When paper is inserted into the throat (2),the lights (4) come on.
The sequence in which the lights (4) come on depends on the
amount of paper inserted into the machine.In order to ensure
optimum shredding,we recommend only the first 4 blue lights be
lit up on the LOAD METER (4).If the paper load increases, the rest
of the lights come on,first the yellow lights,then the red lights to
indicate a paper jam.If the amount of paper inserted axceeds the
load capacity of the machine,the shredder cuts out and the jam
warning light (8) comes on.
The machine then automatically goes into reverse for a few
seconds to free up the cutting blades and stops. Remove the
excess paper from the throat (2) to free the electronic eyes (3)
and then insert a smaller amount of paper into the throat and the
machine automatically starts a new shredding cycle.
It is recommended to limit jams caused by insertion of axcessive
quantities of paper and to operate the machine below its
maximum shredding capacity in order to prolong the life of the
mechanical parts and the machine itself.
All models come with warning lights (5) to tell the operator when
the cutting blades need to be oiled.Just shred a sheet of paper
sprinkled with the KOBRA oil supplied with the machine.Then
press the OIL button (6) to switch off the warning light (5).Now
your shredder is oiled.For models with the built-in oiling system
AUTOMATIC OILER,the warning light (5) flashes when the oil
container is empty and in this case the empty container must be
replaced with a full one.(SEE ACCESSORIES).
About one minute after the replacement of the oil container the
OIL ligth (5) will switch off automatically.
7
Publicidad
