Publicidad
Monitor/Moniteur/Monitor
1
1
4
4
5
7
8
2
1
7
AV-Interface Unit/Unité d'interface audio/vidéo/Instalación del
equipo de conexión AV
1
Power Lead Connection/Raccordement du cordon
d'alimentation/Conexión del cable de alimentación
For the North American Customer/
Pour les clients nord-américains/
Para los clientes de Norte América
1
w
All manuals and user guides at all-guides.com
2
2
3
5
6
6
7
6
3
6
4
8
9
p
5
2
p
e
q
Installation
Installing the Monitor
Caution:
Do not install the monitor near the front passenger seat air bag system.
<Mount it using the supplied bracket>
North American customers are not supplied with a Mounting Bracket; therefore, please use an L-bracket as needed.
Assemble the supplied bracket and mount the monitor temporarily.
Note: Always use the supplied bracket or equivalent.
Verify the installation location.
Select a flat surface and temporarily mount the unit. Use adhesive tape, etc.
Notes:
• Mounting hints
• Top of the monitor does not exceed the top of the dash when viewed from the driver's seat.
• Mounting surface is stable.
• Monitor can be angled for easy viewing.
• In a vehicle with a front passenger air bag, do not install the unit where it will interfere with the operation of the system.
• If the surface of the dash board is finished with other than plastic (true leather, wooden panel, cloth covered panel, etc.),
there will be some damage if the bracket is removed.
• Installation close to other equipment (such as a GPS antenna) may give rise to mutual adverse influences. Please pay
careful attention to the installation location and maintain sufficient space between other equipment.
Remove the monitor from the bracket.
Peel the protective paper from the double-stick tape on the bracket's base.
Clean the mounting location with the cleaner supplied.
Notes:
• Warm the mounting location with a dryer, etc. and then place the bracket into position.
• Do not apply force or moisture for 24 hours after installation.
• If the bracket is not attached securely with just the tape, use the supplied screws to complete the installation.
•
: If the mounted surface is curved slightly, reform the base to fit to its shape.
Connect the connector to the terminal of the monitor.
Mount the monitor on the bracket.
Slide the mounting foot into the bracket on the monitor. Secure the monitor by tightening the locking collar.
Dress the monitor's cable using the cord clamp provided.
Adjust the height and angle of the monitor for easy visibility.
Determine the height and angle. Tighten the height and angle adjusting screws to secure the monitor.
Note: When mounting with other than the attached Mounting Bracket, use the attached L shape bracket depending on usage.
Numbers Identification
1 Mounting Bracket (Not included for the North American Customers.)
2 Monitor
3 Dashboard
4 Double-Stick Tape
5 Mounting Screws (Not included for the North American Customers.)
6 Cord Clamp (Not included for the North American Customers.)
7 Height Adjustment Screw
8 Angle Adjustment Screw
<Mounting to the head rest>
By all means, make a request to your store of purchase for mounting to a headrest.
The following descriptions are directed at the dealer.
Pull the connection cable through the bracket in advance, then, mount the bracket to the head rest.
Connect the connection cable to the monitor, and set the bracket hook to the groove of the monitor rear panel. (Bring the
monitor to the upper side of the bracket and hook.)
Insert the hexagon screw through the plain washer and spring washer, then tighten it with the supplied wrench.
* Please use the attached screw.
Mount the faceplate.
Numbers Identification
1 AV interface unit
2 Connection cable
3 Head rest
4 Bracket
5 Monitor
6 Hook
7 Face plate
8 Plain washer
9 Spring washer
p Hexagon screw
Installing AV Interface Unit
This Unit can be placed inside the trunk, on the kick panel of the front passenger's seat or underdash. However, to avoid
unnecessary signal wiring, it is better to mount the Unit as close as possible to the Display.
DO NOT MOUNT THE INTERFACE UNIT IN LOCATIONS EXPOSED TO MOISTURE OR EXTREME HEAT (such as the
engine compartment).
Velcro fastener Mounting:
1. Place a Velcro fastener onto the mounting surface. The rough side should be facing the unit.
2. Remove the backing to the adhesive on the Velcro strips. Press the unit onto the mounting location.
Numbers Identification
1 Floor/Trunk
2 Velcro fastener (Included)
Connections
Cautions
Make connections correctly.
Improper connections may cause a fire or operation failure.
1
Foot brake lead (Yellow/Black) (For the North American Customer only)
Connect this lead to the foot brake lead powered when the foot brake is pressed.
2
Hand brake lead (Yellow/Blue) (For the North American Customer only)
Connect this lead to the hand brake lead powered when the hand brake is pulled.
3
Parking brake lead (Yellow/Blue) (For Customer in other Countries only)
Connect this lead to the parking brake lead powered when parking brake is pulled.
45 Remote control output lead (White/Brown)
To remote control input lead of ALPINE products used in the system.
6
Back-up lamp signal input/Remote control output lead (AUX3) (Brown/Black)
The connections to be made will differ depending on the equipment that is connected to the AUX3 input connector.
English
Publicidad
