Publicidad
For programming press the pushbutton on the decoder (see picture) before connecting the decoder to the current supply.
Please strictly adhere to the following procedure:
2. How to programme a turnout or signal address on the digital station:
The decoder has to be connected to the main track, not to the programming track. Important: While programming please make
sure that neither a locomotive with address 72 in the Märklin data format nor a locomotive with address 72 in the DCC/NMRA
format are activated on the command unit. Please check this before you continue to programme. In addition we recommend
making a restart of the command unit without deleting the existing database (ATTENTION: Do not make a complete reset of the
system! Please follow the instruction manual of your command unit!). Switch off the power on the track (press button "STOP").
Keep the pushbutton on the decoder (see picture) pressed when you switch on the power on the track again. The red LED of
the decoder flashes now. The decoder can only be programmed with an address group of 4 successive addresses (Example:
1 - 4, 5 - 8, 9 - 12, etc.). The decoder automatically recognizes whether it is a Märklin/Motorola or a DCC address. Now enter
the address for the sawmill / reciprocating saw as a magnetic item.
Important: The first address of the group of 4 successive addresses always controls the function. Send a switching command
and the red LED will go out (in our example: 1, 5, 9, etc.). Depending on the used command unit the highest address which can
be chosen in the Märklin/Motorola format is address 317 and address 2045 in the DCC format. Not all command units send the
complete address range. The decoder checks the switching commands while importing the address. It may happen that you
have to send the switching command several times, especially if various locomotives are activated in different digital formats
while importing. As soon as the red LED goes out, the programming of the decoder is finished. To release the decoder it is
necessary to change the digital format of the memorized magnetic item on some multi-protocol command units. For this purpose
call up the magnetic item and change the data format (Märklin/Motorola <> DCC/NMRA).
Once the decoder is correctly programmed you can choose the following functions:
Address 1 in a group of addresses: The reciprocating saw starts to move. Address 2 in a group of addresses: The light can be
switched on/off. After the reciprocating saw has stopped to move the light is always switched off. In order to support the effect,
the lighting flickers with the move of the reciprocating saw.
3. Märklin Mobile Station 60652 (firm locomotive address):
1. Install a locomotive with address 72.
2. Connect the red cable to the center track and the black cable to the track. Important: Pay attention to the polarity!
3. Press "STOP" on the mobile station (power OFF). Now keep the pushbutton pressed on the decoder (see picture 2) and
press again STOP on the mobile station (power ON).
4. Red LED goes on and out.
The decoder is now programmed with the locomotive address 72. The button "lighting" releases the function and the
reciprocating saw starts to move.
4. ROCO Lokmaus 2 (firm locomotive address):
1. Install a locomotive with address 72.
2. Connect the black cable to the track.
3. Send address: For this purpose press button F1 several times.
4. Keep the button pressed on the decoder (see picture) and connect the red cable to the track (power ON).
5. Red LED goes on and out.
The decoder is now programmed with the locomotive address 72. The button F1 releases the function (the reciprocating saw
moves). Note: Please strictly adhere to this procedure to ensure that the address will be sent. Do not use the button "STOP".
5. You do not remember your decoder address and have to make a decoder RESET
In case you do not remember your decoder address, you can repeat the procedure previously described. If you have memorized
a digital address in your decoder but if you want to analogically operate the reciprocating saw directly with a model railroad
transformer, you have to cancel the digital address. For that purpose switch off the current and connect the pushbutton for the
analog release. Keep the manual release pushbutton as well as the button on the decoder pressed at the same
time and then switch on the current. Now the digital address of the decoder is deleted and you can release the decoder with the
manual release pushbutton.
6. Analog Operation
The release is possible any time with the enclosed pushbutton, however you can also use a control box. ATTENTION: Make
sure that the control box does not have any connection to the traction current or to the transformer. NOTE: The motor is NOT
designed for non-stop operation! If the pushbutton is constantly pressed or short-circuited the sawmill / reciprocating saw
pauses and the red LED of the decoder flashes quickly.
7. Problem Handling: What can I do when the sawmill / reciprocating saw do not work?
In case the programming does not properly work at first time:
1. Carefully read the instructions and repeat the decoder programming. Please wait 3 seconds before you start programming
again.
2. Press the buttons on the command unit longer and more slowly / press the buttons several times.
3.Change the data format of the memorized magnetic item (Märklin/Motorola DCC/NMRA).
NOCH GmbH & Co. KG - Lindauer Straße 49 - D-88239 Wangen im Allgäu
info@noch.de - www.noch.de
Publicidad
