Cleaning Your Appliance - TEFAL Cuisine companion Instrucciones De Uso

0828792_NoticeCuisineCompanion_SM_Mise en page 1 05/12/13 14:59 Page74

CLEANING YOUR APPLIANCE

The appliance should not be
•
immersed. Never put the motor
unit (A) under running water.
Once you have finished using it, disconnect the
appliance.
• Clean the bowl immediately after use.
• Press the locks (D2) then lift the bowl
assembly (D).
• Place the bowl on a flat surface.
• Unlock the lid by rotating one quarter of a turn
clockwise. Carefully remove the lid.
• When the parts have cooled, unclip the seal
holder from the lid with help of the spatula (G)
(See Fig. 15).
• Take care with the knives of the ultrablade
chopping blade (F1) and
kneading/crushing knife (F4) when you are
cleaning them and when you empty the bowl,
they are extremely sharp.
• When the parts have cooled down:
- dismantle the common spindle (D3), the
seal (D4) and the locking ring (D5) (See
Fig. 13).
- clean the bowl (D), the common spindle
(D3), the seal (D4), the locking ring (D5),
the accessories (F1), (F2), (F3), (F4),
(F5), the steam regulator cap (E1), the lid
(E2), the seal holder (E3) and the seal
(E4) using a sponge and some soapy water.
• Rinse these different parts under running water.
• In the event of pronounced clogging, leave to
soak for several hours in water with a little
washing-up liquid added and scrape with the
spatula if necessary (G).
• In the event of scale building up in the bowl,
you can use the rough side of a kitchen sponge.
• To clean the motor unit (A), use a damp cloth.
Dry carefully.
• To help you with cleaning, the bowl, lid
assembly and accessories are dishwasher safe,
with the exception of the common spindle (D3)
and its locking ring (D5) (See Fig. 14).
• The accessories, the detachable common
spindle and the parts of the lid may become
slightly discoloured with certain ingredients
such as curry, carrot juice, etc; this does not
the
represent any danger for your health or for the
operation of your appliance. To avoid this, clean
these parts immediately after use.
74
WHAT TO DO IF YOUR APPLIANCE DOES NOT WORK
PROBLEMS CAUSES
It is not plugged in.
The switch (H) is in position 0.
The appliance does not
work.
The bowl or the lid are not correctly posi-
tioned or locked.
The lid is not fully assembled.
The lid does not lock.
The appliance is not positioned on a flat
surface, the appliance is not stable.
Excessive vibration. Volume of ingredients too high.
Accessory error.
Volume of ingredients too high.
The lid is not correctly positioned or
locked.
The seal is not present.
Leak through lid.
The seal is cut or damaged.
Accessory error.
The seal is not correctly positioned.
Leak through the bowl The seal is damaged.
spindle.
The locking ring (D5) is not locked cor-
rectly.
The blades do not rotate Pieces of food that are too big or too
easily. hard.
Smell from motor. On using the appliance for the first time, or
in the event of overload of the motor cau-
sed by too large a quantity of ingredients
or by pieces that are too hard or too big.
"STOP" is displayed. The appliance has detected too many vi-
brations and has changed to the safety
position.
"SECU" is displayed. Overload of the motor caused by too
large a quantity of ingredients or by
pieces that are too hard or too big.
SOLUTIONS
Plug the appliance into an electrical
socket.
Move the switch to position 1.
Check that the bowl or the lid are cor-
rectly positioned and locked according to
the diagrams in the instruction manual.
Check that the seal is correctly assembled
on the seal holder and that the seal holder
is correctly assembled on the lid.
Place the appliance on a flat surface.
Reduce the quantity of ingredients pro-
cessed.
Check that you are using the recommen-
ded accessory.
Reduce the quantity of ingredients pro-
cessed.
Lock the lid correctly on the bowl.
Position the seal on the seal holder and
clip the assembly to the lid.
Change the seal, contact an approved
service centre.
Check that you are using the recommen-
ded accessory.
Position the seal correctly.
Contact an approved service centre.
Lock the ring correctly (D5).
Reduce the size or quantity of the ingre-
dients processed.
Add some liquid.
Leave the motor to cool and reduce the
quantity of ingredients in the bowl.
Check that you are at the right speed and
that you are using the recommended ac-
cessory.
Leave the motor to cool and reduce the
quantity of ingredients in the bowl.
75