Operating Modes; Starting Operation; Working Advice - Bosch GHO 15-82 Professional Manual Original

OBJ_DOKU-27752-001.fm Page 14 Thursday, September 8, 2011 9:58 AM
14 | English
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suita-
ble for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Clean the chip ejector 3 regularly. Use a suitable tool (e.g., a
piece of wood, compressed air, etc.) to clean a clogged chip
ejector.
Do not reach into the saw dust ejector with your hands.
They could be injured by rotating parts.
To ensure optimum extraction of dust/chips, always work
with external dust extraction or a chip/dust bag.
External Dust Extraction (see figure C)
Mount the vacuum hose 14 (accessory) on to the saw dust
ejector 3.
Connect the vacuum hose 14 to a vacuum cleaner (accesso-
ry). An overview for connecting to various vacuum cleaners
can be found at the end of this manual.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Integrated Dust Extraction (see figure C)
A chip/dust bag (accessory) 15 can be used for smaller jobs.
Insert the sleeve of the chip/dust bag firmly into the chip ejec-
tor 3. Empty the chip/dust bag 15 at regulary intervals to
maintain optimum dust collection.
Operation

Operating Modes

Adjusting the Planing Depth
With the adjustment knob 2, the planing depth can be adjust-
ed variably from 0–1.5 mm using the planing depth scale 1
(scale graduation = 0.1 mm).
Park Rest (see figure D)
The park rest 16 allows the machine to be set down directly
after operation, without danger of damaging the working sur-
face or the planer blade. While planing, the park rest 16 is tilt-
ed upwards thus enabling full contact of the rear part of the
planer base plate 6.
Note: The park rest 16 may not be removed.

Starting Operation

Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
2 609 140 740 | (8.9.11)
Switching On and Off
To start the machine, first push the lock-off button for the
On/Off switch 4 and then press the On/Off switch 5 and keep
it pressed.
To switch off the machine, release the On/Off switch 5.
Note: For safety reasons, the On/Off switch 5 cannot be
locked; it must remain pressed during the entire operation.

Working Advice

Planing (see figure D)
Set the required planing depth and place the front part of the
planer base plate 6 against the workpiece.
Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kickback when
the cutting tool jams in the workpiece.
Switch the machine on and guide the machine with even feed
over the surface to be planed.
To achieve high-grade surfaces, work only with low feed and
apply pressure on the centre of the planer base plate.
When machining hard materials (e.g. hardwood) as well as
when utilising the maximum planer width, set only low planing
depths and reduce planer feed, as required.
Excessive feed reduces the surface quality and can lead to
rapid clogging of the chip ejector.
Only sharp blades achieve good cutting capacity and give the
machine longer life.
The integrated park rest 16 also allows for continued planing
at any given location on the workpiece after an interruption:
– With the park rest folded down, place the machine on the
location of the workpiece where the planing is to be contin-
ued.
– Switch on the machine.
– Apply the supporting pressure onto the front part of the
planer base plate and slowly push the machine forward
( ). This tilts the park rest upward ( ) so that the rear
part of the planer base plate faces on the workpiece again.
– Guide the machine over the surface to be planed ( ) with
even feed.
Beveling Edges (see figure E)
The V-grooves in the front planer base plate allow quick and
easy beveling of workpiece edges. Depending on required
bevel width, use the corresponding V-groove. For this, place
the planer with the V-groove onto the edge of the workpiece
and guide it along the edge.
Groove to be used
none
small
medium
large
Planing with Parallel/Beveling Guide (see figures F–H)
Mount the parallel guide 17 or beveling guide 21 to the ma-
chine using the corresponding fastening bolt 20. Depending
on the application, mount the rebating depth stop 24 with fas-
tening bolt 23 to the machine.
Dimension
a (mm)
0 – 4
2 – 6
4 – 9
6 – 10
Bosch Power Tools