Tabla de contenido
Publicidad
ENGLISH
1) INSTALLATION INSTRUCTIONS
2) DL800S – INSTALLATION AND MAINTENANCE INSTRUCTIONS
3) TOP INLET VERSION
27800 DL800S with soap holder
27802 DL800S without soap holder
4) BUILT-IN INLET VERSION
27812 DL800S with soap holder
27814 DL800S without soap holder
5) PRECAUTIONS FOR USE (The product guarantee depends on the respect for these rules)
INSTALLATION and START UP
For products delivered with filters, these must be installed in accordance with the instructions.
Before commissioning any of our valves, it is essential to carefully bleed the pipes that can damage the mechanisms or water passages
(PRESTO® heads that can be dismantled from front).
Recommended operating pressure according to NF EN 816: 1 to 5 bars.
CLEANING
The chrome-plated coating of PRESTO® valves must be cleaned only with soapy water.
Abrasive, acid, alkaline or ammonia-based household products are prohibited.
MAINTENANCE
Never lubricate the internal mechanism, particularly the caps and valve seals.
6) From 20 minimum to 80 maximum
7) 7 pozidriv screws Ø4.5 mm pins supplied
8) HOT
9) COLD
10) Shut-off valve + bushing to be installed on the Hot Water side (delivered in a pouch)
11) Wall attachment plate
12) INSTALLATION OF TOP INLET VERSION
13) INSTALLATION OF BUILT-IN INLET VERSION
14) Shut-off valve + bushing to be installed on the hot water side (delivered in a pouch)
15) DRAIN BEFORE INSTALLING THE PANEL
16) OPERATION OF THE CONTROLS
17) Pressing this causes the flow to stop
18) Pressing on the lower part triggers the flow.
19) Commissioning
Drain the pipe
Connect and open the shut-off valves.
Press several times on the controls to force the air out
Adjust the angle of the jet
Flow
Delivered with a flow limiter 10 l/min
20) ADJUSTMENT AND MAINTENANCE OF THE THERMOSTATIC CARTRIDGE
The Mixing valve allows the user to select the temperature of the lukewarm water, between the cold water temperature and the lukewarm
water temperature preset at 38° C.
MODIFICATION OF THE MAX OPERATING TEMPERATURE
21) On delivery black line or point Ø1.5 vertically aligned
22) + Hot
23) + Cold
24) Red Ring
25)
25) • Rotate the centre spindle according to the desired temperature: 1 notch = 2° C
25)
25)
• Raise the lever keeping the mark (A) vertical
26)
26) IT IS NOT RECOMMENDED AND DANGEROUS TO DELIVER HOT DOMESTIC SUPPLY WATER AT MORE THAN 42° C
26)
26)
INSTANTANEOUS SHUT-OFF OF THE HOT WATER SUPPLY IN CASE OF ACCIDENTAL RUPTURE OF THE COLD WATER SUPPLY.
27) MAINTENANCE OF THE THERMOSTATIC COMBINATION CARTRIDGE
Clean or replace
Disassembly:
Close the water inlets
Remove the lever (See below)
Remove, clean and reinstall as indicated.
28) Black line or point Ø 1.5 vertically aligned
29) Index on top
30) Stop 38° c
31) Vertical Flats
32)
32)
32)
32) • Reinstall the lever by keeping the mark (A) vertical
33) SETTING THE TIME-DELAY
34) MAINTENANCE OF THE SHOWER
Part no. : 90207 20 safety wires
Part no. : 90186 20 O-rings
Part no. : 90184 1 grille + 1 picot membrane + 1 flow regulator 10l/min
Part no. : 90185 1 grille + 1 picot membrane
Part no. : 90183 Shower priming pump + 2 screws
Part no. : 90719 Shower priming pump + 2 screws
Part no. : 90145 Flow regulator 6 l/min
Part no. : 90178 Flow regulator 8 l/min
Part no. : 90146 Flow regulator 10 l/min
35) MAINTENANCE OF THE PRIMING PUMP AND STOP BUTTON
Close the water inlets
Remove the front face of the panel
36) CONTROL CIRCUIT WIRING LAYOUT
37) RASSEMBLE WHILE RESPECTING THE REVERSE PROCEDURE
38) This document is not contractual; we reserve the right to modify the characteristics of our products without notice.
39) PATENTED and REGISTERED MODELS
Publicidad
Tabla de contenido
