KNOVA KN M-2509RC Manual Del Usuario página 25

OPERATION
NOTE: The chart below references a compound cut for crown molding ONLY WHEN THE ANGLE BETWEEN THE WALLS
EQUALS EXACTLY 90°.
KEY BEVEL SETTING
Inside corner-Left side
IL 33.9º
Inside corner-Right side
IR 33.9º
Outside corner-Left side
OL 33.9º
Outside corner-Right side
OR 33.9º
CROWN MOLDING CHART
Compound Miter saw
Miter and bevel Angle settings Wall to Crown Molding Angle
52/38" Crown Molding
Angle
Miter
Between
Setting
Walls
67 42.93
68 42.39
69 41.85
70 41.32
71 40.79
72 40.28
73 39.76
74 39.25
75 38.74
76 38.24
77 37.74
78 37.24
79 36.75
80 36.27
81 35.79
82 35.31
83 34.83
84 34.36
85 33.90
86 33.43
87 32.97
88 32.52
89 32.07
90 31.62
MITER SETTING
31.6° Right
31.6° Left
31.6° Left
31.6° Right
45/45" Crown Molding
Bevel Miter
Setting Setting
41.08 46.89
40.79 46.35
40.50 45.81
40.20 45.28
39.90 44.75
39.61 44.22
39.30 43.70
39.00 43.18
38.69 42.66
38.39 42.15
38.08 41.64
37.76 41.13
37.45 40.62
37.13 40.12
36.81 39.62
36.49 39.13
36.17 38.63
35.85 38.14
35.52 37.66
35.19 37.17
34.86 36.69
34.53 36.21
34.20 35.74
33.86 35.26
1. Position top of moulding against fence.
2. Miter table set at RIGHT 31.6°.
3. LEFT side is finished piece.
1. Position bottom of moulding against fence.
2. Miter table set at LEFT 31.6°.
3. LEFT side is finished piece.
1. Position bottom of moulding against fence.
2. Miter table set at LEFT 31.6°.
3. RIGHT side is finished piece.
1. Position top of moulding against fence.
2. Miter table set at RIGHT 31.6°.
3. RIGHT side is finished piece.
Angle
Bevel
Between
Setting
Walls
91
36.13
92
35.89
35.64 93
94
35.40
95
35.15
34.89 96
34.64 97
98
35.38
99
34.12
33.86 100
33.60 101
102
33.33
33.07 103
32.80 104
105
32.53
106
32.25
31.98 107
31.70 108
109
31.42
31.34 110
30.86 111
112
30.57
113
30.29
30.00 114
24
TY P E OF C U T
52/38" Crown Molding
Miter Bevel
Setting Setting
31.17 33.53
30.73 33.19
30.30 32.86
29.86 32.51
29.43 32.17
29.00 31.82
28.58 31.48
28.16 31.13
27.74 30.78
27.32 30.43
26.91 30.08
26.50 29.73
26.09 29.38
25.69 29.02
25.29 28.67
24.89 28.31
24.49 27.96
24.10 27.59
23.71 27.23
23.32 26.87
22.93 26.51
22.55 26.15
22.17 25.78
21.79 25.42
45/45" Crown Molding
Miter Bevel
Setting Setting
34.79 29.71
34.33 29.42
33.86 29.13
33.40 28.83
32.94 28.54
32.48 28.24
32.02 27.94
31.58 27.64
31.13 27.34
30.68 27.03
30.24 26.73
29.80 26.42
29.36 26.12
28.92 25.81
28.48 25.50
28.05 25.19
27.62 24.87
27.19 24.56
26.77 24.24
26.34 23.93
25.92 23.61
25.50 23.29
25.08 22.97
24.66 22.66