Comparing Picture Adjustments On The Screen; Sound Adjustments - Pioneer PDP-5080HD Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Adjustments and Settings
Field NR
Removes glimmer for more natural images
Selections
Off
Deactivates Field NR
High
Enhanced Field NR
Mid
Standard Field NR
Low
Moderate Field NR
7
Press HOME MENU to exit the menu.
Comparing picture adjustments on the
screen
During picture adjustments, you can quickly refer to the image
previously set in the same parameter, allowing you to easily
compare and select the preferred image quality.
1
Press HOME MENU.
2
Select "Picture" ( /
then ENTER).
3
Select an item to be adjusted ( /
4
While performing adjustment, press BLUE on the
remote control unit.
"Before" displays and the image adjusted last time appears for
comparison.
Before
5
Press the button again to return to the newly adjusted
image.
Each press of the button toggles between "Before" and "After".
6
Repeat steps 1 and 5 for other parameters.
7
Press HOME MENU to exit the menu.
Caution
• If you exit the menu by pressing HOME MENU or no operation
is performed for 60 seconds, all the parameter settings
displayed last are stored in memory.
• If you want to exit the menu without performing the
adjustments (or leaving the settings disabled) on the "After"
screen, switch to "Before" and then exit.
Note
• You cannot adjust any item while on the "Before" screen. A
warning message appears.
• When you switch to another parameter, make sure to change
the display from "Before" to "After" first, otherwise you cannot
select "Before". A warning message appears if you don't.
• If you exit the selection from the "Before" screen, the previous
entry is stored in the memory and the button no longer works.
• If you exit the selection from the "After" screen, the new entry
is stored in the memory and the button no longer works.
• If you move and change the "AV Selection" parameter, the new
entry in the current parameter is stored in the memory and the
button continues to work.
• You cannot compare images between different parameters on
the "AV Selection" menu ("STANDARD" and "MOVIE", for
example).
• When you select this function, "OPTIMUM" on the "AV
Selection" menu and "Room Light Sensor" on the "Option"
menu are set to off and image quality returns to default
settings.
• This function is not selectable:
- when you select "AV Selection",
- when you select "Yes" or "No" on the confirmation screen for
- when you select a menu from the PC source

Sound adjustments

You can adjust the sound quality to your preference with the
following settings.
Adjust the sound to your preference for the chosen AV Selection
option. See page 54.
1
2
then ENTER).
3
4
Item
Treble
Bass
Balance
5
• You cannot adjust the sound for listening with headphones.
• If you perform sound adjustments with headphones
connected, the new settings will become effective as soon as
you disconnect the headphones.
• To restore the factory defaults for all the items, press
select "Reset" in step 3, and then press ENTER. A confirmation
screen appears. Press
ENTER.
"Reset" from the "Picture" menu or
Press HOME MENU.
Select "Sound" ( /
then ENTER).
Select an item to be adjusted ( / ).
Select the desired level ( / ).
Sound
STANDARD
Treble
Bass
Balance
Reset
Sound Effect
button
For weaker treble
For weaker bass
Shifts the audio balance to
the left
Press HOME MENU to exit the menu.
Note
/
to select "Yes", and then press
11
2
0
0
button
For stronger treble
For stronger bass
Shifts the audio balance to
the right
/
to
57
En

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Pdp-4280hd

Tabla de contenido