Cleaning Mode; Configuration Mode - Bradley Verge LVQ Serie Manual Del Usuario

Sistema de lavabo con tecnología washbar
Ocultar thumbs Ver también para Verge LVQ Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Installation

Cleaning Mode

Cleaning mode temporarily locks out the WashBar for approximately 30 seconds. All of the sensors (soap, water, dryer) are
inactive in this mode. After 30 seconds, the WashBar will exit Cleaning Mode and return to Standby/Idle Mode. Use a soft cloth
and ethyl alcohol or water to clean WashBar access plates/sensor windows.
To activate Cleaning Mode:
1. Place a hand under the dryer and then immediately (within 1 second) under the soap sensor and hold hands under both
dryer and soap sensors for approximately 5 seconds until all LED lights turn solid white.
2. Remove hands only when all LED lights turn solid white.
LED lights may flash and cycle different colors. To activate this mode, only remove hands once all LED lights are solid
white.

Configuration Mode

Configuration Mode is when the user can configure the WashBar or obtain cycle counts for soap, water and dryer. All of the
sensors (soap, water, dryer) are active in this mode. After 10 seconds of no use, the WashBar will slow flash all LEDs green and
then return to Standby/Idle Mode.
To activate Configuration Mode:
1. Place a hand under the dryer and then immediately (within 1 second) under the soap sensor and hold hands under both
dryer and soap sensors for approximately 10 seconds until all LED lights turn solid red.
2. Remove hands only when all LED lights turn solid red.
LED lights may flash and cycle different colors. To activate this mode, only remove hands once all LED lights are solid
red.
While in Configuration Mode, LED lights will be solid red unless changing configurations or getting cycle counts.
Cycle Counts
To display cycle counts, while in Configuration Mode:
1. Place and remove hand within 3 seconds under the device you want to get a cycle count for (soap, water, dryer).
2. The LED light for that device will turn green to indicate the count will follow.
3. The LED light for that device will turn solid red and then flash the number of cycles as follows:
• Soap: the LED flashes the number of 100,000 cycles for the device.
• Water: the LED flashes the number of 10,000 cycles for the device.
• Dryer: the LED flashes the number of 1,000 cycles for the device.
For example, a water activation cycle of 248,000 will be displayed in the following order: A solid green water LED, followed by
a 1.5 second solid red soap LED, followed by 2 white soap LED flashes (indicating the 2 in 248,000). Next, there will be a 1.5
second solid red water LED followed by 4 white soap LED flashes (indicating the 4 in 248,000). Finally, a 1.5 second solid red
dryer LED followed by 8 white soap LED flashes (indicating the 8 in 248,000).
Setting the Soap Type
If the WashBar is set to the correct soap type, the low soap indicator will display low soap at 80% empty as intended. If not set
correctly, a liquid soap system will be empty before indicator lights up if set to foam and a foam soap system will be 60% empty if
set to liquid.
To set soap type, while in Configuration Mode:
1. Hold hand under soap sensor for 5 seconds to start selection process. Selection options will cycle until hand is removed.
2. Continue to hold hand under soap until desired setting color is shown then remove hand while color is being displayed.
• Red LED: Liquid Soap (3200 dispensing cycles occur before low soap counter needs to be reset. This is the Default
setting when WashBar is reset.)
• Blue LED: Foam Soap (4000 dispensing cycles occur before low soap counter needs to be reset.)
Bradley • 215-1842 Rev. H: ECO 20-08-028B
1/21/2021
LVQD1
25

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Verge lvqd1

Tabla de contenido