ELICA BMECH9WVSS Montaje Y Modo De Empleo página 13

Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Model with touch panel
To select the functions of the hood just touch the commands.
Light key ON/OFF
Intensive speed selection key (suction power) -
duration 5 minutes - press again to return to
previous setting.
High-speed selection key (suction power).
Medium-speed selection key (suction power) -
when flashing it indicates the need to wash or
replace the carbon filter. This signal is normally
deactivated. To activate the alarm, disable the
electronic by pressing the 0 button for 3 seconds.
Next, simultaneously press buttons 1 and 2 for 3
seconds; at first, only button 1 will flash, then both
buttons 1 and 2 will flash to indicate activation.
Repeat the procedure to deactivate the alarm; at
first buttons 1 and 2 will flash and subsequently
only button 1 to indicate deactivation.
Low-speed selection key (suction power) – when
flashing it indicates the need to wash the fats filter.
Motor key OFF (stand by) – excludes the
electronics – reset wash/replace filters signals.
MOTOR OFF
Press briefly to switch the motor off.
RESET FILTERS SIGNALS
In functioning mode, after carrying out filter
maintenance, press the key until hearing the sound
signal. The flashing LED 1 (grease filter) or 2
(carbon filter) stops flashing.
EXCLUDING THE ELECTRONICS
Press the key for 3 seconds. The hood command
electronics will be excluded.
This function can be useful during the product
cleaning operations.
Just repeat the operation to reinsert the
electronics.
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Model with 5 push-buttons control panel
T1. Button ON/OFF lights (Led L1 lit)
T2. Button OFF – Selection button suction speed (power)
1 (Led L2 lit)
T3. Selection button suction speed (power) 2 (Led L2+L3
lit)
T4. Selection button suction speed (power) 3 (Led
L2+L3+L4 liti)
T5. Selection button intensive suction speed (power)
(Led L2+L3+L4 lit + Led L5 flashing) - duration 5 minutes
– after which the hood automatically sets suction speed
(power) 2.
Delayed switch-off of the hood (flashing LEDs):
It is possible to set the delayed hood switch-off by pressing
again for more than 2 seconds the button of the suction speed
(power) active at that time.
The available delayed switch-off options are:
Suction speed (power) 1: 20 minutes
Suction speed (power) 2: 15 minutes
Suction speed (power) 3: 10 minutes
Intensive suction speed (power): 5 minutes
Filter saturation indicator
The hood is equipped with a function that warns the user, at
regular time intervals, when the filters are saturated and it is
necessary to perform their maintenance.
Grease filter saturation indicator: With the hood off (OFF)
all suction speed (power) LEDs light up with steady light for 40
seconds.
Activated charcoal filter saturation indicator: With the
hood off (OFF) all suction speed (power) LEDsflash for 40
seconds.
Activation of the active charcoal filter saturation
signal: normally, this function is disabled; to activate it,
switch off the hood (OFF) and simultaneously press
buttons T3 and T5 for more than 3 seconds. LEDs L3
and L5 will start flashing.
To disable repeat the operation: LEDs L3 and L5 light up
with steady light.
Resetting the filters' saturation indicator:
With the hood on (ON) press button T2 for more than 2
seconds; all LEDs will light up briefly.
Note: if necessary, repeat the operation in case both
indicators (grease filter and activated charcoal filter) are
active.
13