Brew Unit Washing; Rinsing; Descaling The Machine - LAVAZZA BLUE LB2300 Instrucciones Para El Uso

Lavazza
Ready
Insert capsule
On the main page, press button (17) to enter program-
ming mode.
Press button (19) until you see the following page:
2.
Cup warming
To activate the cup-warming surface, press button (15)
to enter the activation page.
2.1
Activate?
No
^
In this case the cup-warming surface is deactivated.
Press button (19) to view the options.
2.1
Activate?
Yes
^
Press button (15) to confi rm and then button (21).
Exit as described in section 7.7.
7.3

Brew unit washing

Washing of the brew unit by the user may
only be performed as described in this sec-
tion.
This cycle allows the cleaning of all parts involved in
the brewing of coffee.
Lavazza
Ready
Insert capsule
On the main page, press button (17) to enter program-
ming mode.
Press button (19) until you see the following page:
3.
Brew unit wash
To activate the wash cycle, press button (15) to enter
the activation page.
3.1
Brew unit wash
No
^
In this case washing will NOT be performed.
Press button (19) to view the option
3.1
Brew unit wash
Yes
^
Press button (15) to confi rm.
The machine washes the brew unit by dispensing
water via the dispensing spout.
When the wash cycle is complete, exit as described
in section 7.7.
Use of the machine - User Manual
7.4

Rinsing

This menu allows programming the rinse cycle descri-
bed in section 4.5.
The rinse cycle may be automatically started at diffe-
rent times according to the settings.
Lavazza
Ready
Insert capsule
On the main page, press button (17) to enter program-
ming mode.
Press button (19) until you see the following page:
4.
Rinsing
To access rinse setting, press button (15).
In the following page you can set some automatic rinse
programs which will be carried out in specifi c occa-
sions.
4.1
At the start?
From this page you can set the automatic rinse cycle
each time the machine is switched on.
The rinse cycle is performed at every ma-
chine start-up only if the temperature of the
boiler is lower than 50°C; the cycle starts once the
warm-up phase has ended.
To activate the programming, press button (15) to enter
the page.
4.1.1
Activate?
No
^
In this case the programming is deactivated.
Press button (19) to view the option:
4.1.1
Activate?
Yes
^
Press button (15) to confi rm. The machine will carry out
a rinse cycle each time the machine is switched on.
Press button (19) to view the option:
4.2
Each 24 hrs.
From this page you can set the automatic rinse cycle
every 24 hours starting from option activation. In this
case after 24 hours, the display shows:
Lavazza
Rinsing
C to terminate
Enter to confirm
To activate the programming, press button (15) to enter
the page.
4.2.1
Activate?
No
^
In this case the programming is deactivated.
Press button (19) to view the option:
4.2.1
Activate?
Yes
^
Press button (15) to confi rm. The machine will carry out
a washing of the unit every 24 hours.
The rinse cycle described above may be
carried out only if the machine is switched
on. In case the interval has expired and the ma-
chine is switched on but in Stand-by mode, the
rinse cycle will be carried out when the machine is
switched on again.
Both programming modes may be activated
at the same time.
7.5

Descaling the machine

Limescale forms as the appliance is used; when
the machine requires a descaling cycle, the display
shows:
Lavazza
Ready
Descaling
In this case the machine can still be used normally to
brew coffee; a descaling cycle should be performed.
Descaling of the machine should be per-
formed as soon as possible in order to
guarantee correct functioning of the machine and
signifi cant energy savings.
Warning. To avoid damaging the machine,
do not under any circumstances use wine
vinegar!
Warning. If a fi lter for limescale reduction
has been installed, remove it from the water
tank before introducing the descaling solution.
The purpose of descaling is to eliminate all accumulat-
ed limescale from the surfaces and holes of the water
circuit, guaranteeing perfect functioning of the valves,
warm-up commands and other important components.
Important. Given the complexity of the
machine's water circuit, the descaling
cycle described below does not affect all ducts.
Components such as the brew unit and the plastic
pin/valve connecting to it are excluded.
The descaling operation should be performed regularly,
every 3 to 4 months. In areas with very high water hard-
ness, more frequent descaling is advisable.
Press button (17) to access the main menu.
Press button (19) until you see the following page:
5.
Descaling
Press button (15) to access the descaling function.
The display shows:
5.1
Do it now
Press button (15) again; the display shows:
5.1
Do it now
No
^
Press button (19).
The display shows:
5.1
Do it now
Yes
^
• 29 •