Peg-Perego IGCD0554 Empleo Y Manutencion página 7

CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP EDGE
HAZARD.
1 • Place the seat on its base. Please note: The seat can be installed in 2 different positions, as shown in the figure.
2 • Secure the seat in the desired position with the 2 screws provided.
3 • Insert the seat and base assembly in the 2 slots in the chassis.
4 • Secure it at the rear with the 2 screws provided.
5 • Insert the roll bar in the rear fender assembly, as shown in the figure.
6 • Secure it with the 2 screws provided.
7 • Place the hood on the chassis. Insert the loose end of the black hinge into the 2 slots in the chassis until they lock. Rotate the hood down, making sure it fits
correctly over the simulated engine panels. Place the black hood latch key through the hood and into the chassis. Turn to lock the hood in place.
8 • Click together the 2 parts of the steering wheel.
9 • Push the steering column up from below and slot the steering wheel onto it.
10 • Line up the holes in the steering column and the steering wheel. Secure the steering wheel with the screw and the nut: the nut goes in the hexagonal hole and
the screw in the round hole.
11 • Put the silver decals (for reflective taillights) on the rear fenders.
12 • Install the taillight lenses; slot in the lower part first and then the upper part, as shown in the figure.
13 • Put the silver decals on the grill (for reflective headlights), then install the clear plastic headlight lense.
Follow the instructions below to assemble the trailer.
14 • Insert one of the 4 self-locking washers (there are 2 spares) in the special tool provided. PLEASE NOTE: The tabs on the self-locking washer must face towards
the inside of the tool (see detail A).
15 • Remove the axle from the packaging and take off its protective caps. Use a hammer to drive the axle all the way down into the tool provided, then remove the
tool.
16 • Place wheel bushings into the wheels; large end fits inside the wheel. Then place these components onto the axles, in this order: a washer, a wheel (hubcap end
toward washer) 2nd wheel (hubcap facing outward), a washer (4 washers are provided, 2 of which are
17 • Put a self-locking washer in the special tool. Place the tool over the unsecured end of the axle and hit it with a hammer.
18 • Install the axle assembly onto the bottom of the trailer.
19 • Insert the red clip in the tongue of the trailer.
20 • Press the pegs firmly into the holes in the bed as shown.
21 • Assemble the 3 sides of the trailer. Ensure that the parts with the wooden effect are facing outwards.
22 • Place the assembled parts into the slots in the body of the trailer.
23 • Install the 2 small hubcaps onto the wheels of the trailer.
24 • To attach the trailer to the tractor, insert the clip on the trailer in the hole at the back of the tractor and turn it (see fig. 25).
25 • Position 1: The trailer can be removed. Position 2: The trailer is attached. PLEASE NOTE: The weight capacity of the trailer is 22 lbs - 10 kg.
26 • DRINK HOLDER: A convenient drink holder situated near the seat.
27 • ADJUSTING THE PEDALS: The pedals can be put in 2 different positions to cater to the height of the child. POSITION A (the upper one) is for smaller
children and POSITION B (the lower one) is for bigger children. The 2 positions are marked with 2 different colored dots on the corresponding sticker.
Remove the 3 screws holding the pedal adjustment disk (which are shown on the sticker with symbols) and rotate it to the desired position, then tighten the 3
screws. PLEASE NOTE: Put both adjustment disks in the same position (upper or lower) on both sides.
28 • ADJUSTING THE SEAT: The seat can be put in 2 different positions to cater to the growth of the child. See figure 1 for details.
29 • OPENING HOOD: Use a coin to turn the black hood latch key as far as the position shown in the figure. Inside the hood is a large storage compartment.
DON'T STOP THE FUN
For your child's safety: please read and follow all instructions below before operating.
• ATTENTION:
Check the fastening retainers to be sure they are tight.
Teach your child the proper use of this vehicle for a safe and fun play time.
• Before starting be sure that the way is free from people and objects.
• Drive with both hands steering wheel and keep your eyes on the road at all times.
• Please teach your child to stop in time to avoid running into objects or people.
ASSEMBLY INSTRUCTIONS
TRAILER
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
RULES FOR SAFETY DRIVING
spares).