Descargar Imprimir esta página
Ocultar thumbs Ver también para E-100-A:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

E-100-A
High-Profile End Seal Installation Instructions
APPROVALS
Hazardous Locations
Class I, Div. 2, Groups A, B, C, D
Class II, Div. 2, Groups E, F, G
Class III
– WS
CLI, ZN1, AEx e II T*
Ex e II T*
Ex e IIC T* Gb
E-100-A is IECEx certified for use with:
BTV-CR/BTV-CT:
IECEx
QTVR-CT:
XTV-CT:
KTV-CT:
VPL-CT:
(1)
Except VPL
* For system Temperature Code, see heating cable or design documentation
(2)
Except KTV-CT
KIT CONTENTS
Item
Qty
A
1
B
1
C
1
D
1
WARNING:
This component is an electrical device that
must be installed correctly to ensure proper
operation and to prevent shock or fire. Read
these important warnings and carefully follow all
of the installation instructions.
• To minimize the danger of fire from sustained
electrical arcing if the heating cable is
damaged or improperly installed, and to
comply with the requirements of nVent,
agency certifications, and national electrical
codes, ground-fault equipment protection
must be used. Arcing may not be stopped by
conventional circuit breakers.
(1)
(2)
IECEx BAS 06.0043X
IECEx BAS 06.0045X
IECEx BAS 06.0044X
IECEx BAS 06.0046X
IECEx BAS 06.0048X
.
Description
End seal assembly
Cable lubricant
End seal label
Cable tie
• Component approvals and performance are
based on the use of nVent - specified parts
only. Do not use substitute parts or vinyl
electrical tape.
• The black heating cable core and fibers are
conductive and can short. They must be
properly insulated and kept dry.
• Keep components and heating cable ends dry
before and during installation.
• Bus wires will short if they contact each other.
Keep bus wires separated.
• Use only fire-resistant insulation materials,
such as fiberglass wrap or flame-retardant
foam.
DESCRIPTION
The nVent RAYCHEM E-100-A is a NEMA 4X-rated end seal
kit. It is designed for use with nVent RAYCHEM BTV-CR, BTV-
CT, QTVR-CT, XTV-CT, KTV-CT and VPL-CT industrial parallel
heating cables. Once installed, the end seal is easily re-entered
for maintenance; the heating cable can be accessed without
removing the end seal.
This kit may be installed at temperatures as low as –40°F
(–40°C). For easier installation store above freezing until just
before installation.
For technical support call nVent at (800) 545-6258.
TOOLS REQUIRED
• Wire cutters
• Slotted screwdriver or nutdriver
ADDITIONAL MATERIALS REQUIRED
• nVent RAYCHEM GT-66 or GS-54 glass cloth tape
• Pipe strap
OPTIONAL MATERIALS
• Small pipe adapter for 1 in (25 mm) and smaller pipes:
Catalog number JBS-SPA   P/N E90515-000
• For boot replacement order E-100-BOOT-5/PACK   P/N 281053-000
Cap
Strain
relief
Boot
Leash
Stand
A
CAUTION:
• Leave these installation instructions with the
user for future use.
HEALTH HAZARD: Prolonged or repeated
contact with the sealant in the end seal
boot may cause skin irritation. Wash hands
thoroughly. Overheating or burning the sealant
will produce fumes that may cause polymer
fume fever. Avoid contamination of cigarettes
or tobacco. Consult MSDS VEN 0058 for further
information.
CHEMTREC 24-hour emergency telephone:
(800) 424-9300
Non-emergency health and safety information:
(800) 545-6258.
• Utility knife
D
C
B

Publicidad

loading

Resumen de contenidos para nVent RAYCHEM E-100-A

  • Página 1 E-100-A High-Profile End Seal Installation Instructions DESCRIPTION The nVent RAYCHEM E-100-A is a NEMA 4X-rated end seal kit. It is designed for use with nVent RAYCHEM BTV-CR, BTV- CT, QTVR-CT, XTV-CT, KTV-CT and VPL-CT industrial parallel heating cables. Once installed, the end seal is easily re-entered for maintenance;...
  • Página 2 Heating Cable Types Outer jacket Braid Outer Outer jacket Braid Inner jacket jacket Braid Heating element Inner jacket Inner jacket Bus wire connection Conductive fiber Clear jacket Conductive core Spacer Insulated bus wire Bus wire Bus wire VPL-CT BTV-CR, BTV-CT, QTVR-CT XTV-CT, KTV-CT •...
  • Página 3 BTV and QTVR XTV and KTV • Lightly score outer jacket around and 1 1/8 in down as shown. (28 mm) • Bend heating cable to break jacket at the • Lightly score outer score, then peel off jacket around and 1 1/4 in jacket.
  • Página 4 • Pull heating cable back through bottom of end seal stand CAUTION: Health until braid is just visible above strain relief. Use cable Hazard. Wash lubricant if needed. hands after contact with sealant. Consult material safety data sheet VEN 0058. Braid Strain relief...
  • Página 5 E-100-A Re-entry Instructions • Unscrew cap from end seal stand. WARNING: Shock Hazard. Conductors will be exposed. Re-entry should only be performed by qualified personnel. Follow standard electrical lockout procedures before opening end seal. • Turn off power. • Clip cable tie and remove.
  • Página 6 North America Tel +1.800.545.6258 Fax +1.800.527.5703 thermal.info@nvent.com Europe, Middle East, Africa Tel +32.16.213.511 Fax +32.16.213.604 thermal.info@nvent.com Asia Pacific Tel +86.21.2412.1688 Fax +86.21.5426.3167 cn.thermal.info@nvent.com Latin America Tel +1.713.868.4800 Fax +1.713.868.2333 thermal.info@nvent.com nVent.com ©2018 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice.
  • Página 7 E-100-A Proteção Final De Perfil Alto Instruções De Instalação DESCRIÇÃO O nVent RAYCHEM E-100-A é um kit de proteção final com a classificação NEMA 4X. É projetada para uso com cabos paralelos de aquecimento industrial modelos nVent RAYCHEM BTV-CR, BTV- CT, QTVR-CT, XTV-CT, KTV-CT e VPL-CT da RAYCHEM.
  • Página 8 AVISO: CUIDADO: Este componente é um dispositivo elétrico peças de reposição alternativas ou fita isolante RISCO PARA A SAÚDE: o contato prolongado que deve ser instalado corretamente para de vinil. ou repetido com o vedante na proteção do assegurar operação adequada e prevenir terminal final pode causar irritação da pele.
  • Página 9 • Determine o tipo de cabo aquecedor e continue como mostrado. Vá para o passo 4A Vá para o passo 4B BTV e QTVR Vá para o passo 4B XTV e KTV BTV y QTVR • Corte ligeiramente ao XTV y KTV redor da capa externa e longitudinalmente como 28 mm...
  • Página 10 • Puxe o cabo de aquecimento para trás através da parte CUIDADO: Risco para a inferior do suporte do terminal final até que a blindagem fique saúde. Lave as mãos visível acima do alívio de tensão. Use lubrificante de cabo se depois de entrar em necessário.
  • Página 11 Instruções de reintrodução da E-100-A • Desparafuse a tampa do suporte do terminal final. AVISO: Perigo de choque elétrico. Os condutores serão expostos. A reintrodução só deve ser executada por pessoal qualificado. Siga os procedimentos de desligamento elétrico padrão antes de abrir o terminal final. • Desligue a alimentação.
  • Página 12 América Do Norte Tel +1.800.545.6258 Fax +1.800.527.5703 thermal.info@nvent.com Europa, Oriente Médio, África Tel +32.16.213.511 Fax +32.16.213.604 thermal.info@nvent.com Ásia Pacífico Tel +86.21.2412.1688 Fax +86.21.5426.3167 cn.thermal.info@nvent.com América Latina Tel +1.713.868.4800 Fax +1.713.868.2333 thermal.info@nvent.com nVent.com ©2018 nVent. Todas as marcas e logotipos nVent pertencem ou são licenciados pela nVent Services GmbH ou seus afiliados. Todas as outras marcas comerciais pertencem aos seus respectivos proprietários.
  • Página 13: Descripción

    E-100-A Sello Final Instrucciones De Instalación DESCRIPCIÓN El kit de sello final nVent RAYCHEM E-100-A tiene calificación NEMA 4X. Está diseñado para su uso con los cables calefactores paralelos de aplicación industrial RAYCHEM BTV-CR, BTV-CT, QTVR-CT, XTV-CT, KTV-CT y VPL-CT. Una vez instalado el sello final, es fácil volver a acceder a él para su mantenimiento;...
  • Página 14: Riesgo Para La Salud

    exclusivo de piezas especificadas Deben aislarse de manera adecuada y sí. Mantenga los cables de bus por nVent. No utilice otras piezas mantenerse secos. separados. alternativas ni cinta de vinilo para • Mantenga secos los componentes y • Utilice sólo material aislante ignífugo, electricidad.
  • Página 15 BTV y QTVR • • XTV y KTV • Corte ligeramente la funda exterior alrededor y a lo largo 28 mm como se indica. (1 1/8 pulg.) • Corte ligeramente • Doble el cable la funda exterior calefactor para 32 mm alrededor y a lo (1 ¼...
  • Página 16 • Tire del cable calefactor a través de la base del sello final PRECAUCIÓN: Riesgo hasta que la malla quede visible sobre la protección contra para la salud. Lávese las tirones. Si es necesario, utilice lubricante para cables. manos después del contacto con el sellador.
  • Página 17 Instrucciones de acceso a E-100-A • Desatornille la tapa del soporte del sello final. ADVERTENCIA: Riesgo de descarga eléctrica. Los conductores quedarán expuestos. El acceso sólo debe realizarlo personal calificado. Siga los procedimientos habituales de desconexción eléctrica antes de abrir el sello final. • Desconecte la alimentación.
  • Página 18 North America Tel +1.800.545.6258 Fax +1.800.527.5703 thermal.info@nvent.com Europe, Middle East, Africa Tel +32.16.213.511 Fax +32.16.213.604 thermal.info@nvent.com Asia Pacific Tel +86.21.2412.1688 Fax +86.21.5426.3167 cn.thermal.info@nvent.com Latin America Tel +1.713.868.4800 Fax +1.713.868.2333 thermal.info@nvent.com nVent.com ©2018 nVent. Todos los logotipos de nVent son propiedad o se han cedido bajo licencia a nVent Services GmbH o sus filiales. Todas las otras marcas comerciales son propiedad de sus respectivos dueños. nVent se reserva el derecho de modificar las especificaciones sin previo aviso.