Cequent Performance Products 24947 Instrucciones De Instalación página 3

Always wear SAFETY GLASSES
when installing hitch
Existing M10
Flange Nuts
(6) Places
Bumper Beam
Rear
Existing M8
Flange Head Bolts
(2) Places
1. Remove fascia -
a.) using a T15 torx bit, remove (5) screws from inside of wheel well, both sides.
b.) using a 7mm socket, remove (1) screw located vertically in the upper area of wheel well, behind wheel well liner, both sides.
c.) using a T15 torx bit, remove (8) screws from underbody panel near the wheel wells, (5) on driver's side, (3) on passenger's side.
d.) using a 7mm socket, remove (5) screws from the under body panel to fascia.
Remove taillights - Open trunk. Using a T15 torx bit, remove (2) screws from taillight housing and a Philips head screw driver to remove (1) screw from taillight housing, both sides.
2.
Gently pull the taillights rearward. Disconnect the wiring from taillights.
Remove fascia - using a plastic trim panel tool, gently remove the plastic fascia starting at the outer edges near the wheel wells. Disconnect the wiring from fascia if equipped.
3.
Remove exhaust hanger - using a 13mm socket, remove the (2) bolts from the exhaust hanger. Unhook the exhaust hanger from the hooks on end panel.
4.
NOTE: Support the exhaust before unhooking the exhaust hanger.
Remove bumper beam - using an 15mm deep wall socket with 6" extension, remove (6) flange hex nuts holding bumper beam to end panel. See Figure 1.
5.
Trim underbody panel - using a tape measure, tape, & tin snips, mark & trim the underbody panel as shown in figure 2.
6.
Note: The underbody panel may be trimmed in place or optional to fully remove the panel for trimming.
Hitch installation - raise hitch and bumper beam into position aligning holes with studs in the end panel. Sandwich the hitch between bumper beam and end panel. See Figure 1.
7.
Reinstall fasteners - loosely reinstall the existing (6) M10 hex flange nuts onto the studs, (3) per side.
8.
Reinstall exhaust hanger - reattach the exhaust hanger over the hooks on end panel and install the (2) M8 bolts.
9.
10. Tighten all M10 fasteners with torque wrench to 38 Lb.-Ft. (52 N*M)
11. Tighten all M8 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M)
12. Reinstall the underbody panel if removed in step 6.
13. Reinstall fascia and taillights - Be sure to reconnect all wiring to the fascia and taillights.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which
has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety
specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2016 Cequent™ Performance Products, Inc. - Printed in Mexico
Installation Instructions
PART NUMBERS: 24947, 77334, CQT24947
Bumper End Panel
Figure 1
Exhaust Hanger
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Underbody Panel
Authorized Drawbar Kit:
3593 (Sold Separately)
Drawbar must be used in
the RISE position only.
Sheet 3 of 21 24947NP
3-1/2"
5-1/2"
3-3/4"
Trim
Figure 2
Scan for step by step
PHOTO installation
instruction or visit
http://www.cequentgroup
.com/qr-product.aspx
9-19-16 Rev. B