Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Equipment Required:
Fastener Kit: 01130-708
Wrenches: 3/4, 13/16, 7/8
Drill Bits: 9/16
Hitch requires 5/8" pin and clip.
j
Qty. (4)
9/16-18 X 1.75 GR5 Hex Bolt
k
Qty. (4)
3/8 X 1-1/2 X 3 Block
l
Qty. (6)
Flanged Locknut
m
Qty. (2)
9/16-18 X 1.50 GR5 Hex Bolt
Warning: Under no circumstances is this hitch to be installed on vehicles with a 6' box (short wheelbase).
1.
Remove the spare tire and carrier from the vehicle.
2.
Vehicles W/O Factory Step Bumper: Using the existing holes in the frame rails, bolt the reinforcement brackets into the inside
of each frame rail using 1/2" X 1.25 hex bolts, 1/2" hex nut and lock washers in the two top holes in each bracket. The
reinforcement brackets should rest tightly against the rail lower flanges.
2.
Vehicles W/ Factory Step Bumper: Remove the nuts from the bolts attaching the bumper brackets to the frame rails. Install
the reinforcement brackets into the inside of each frame rail over the bolts and reattach the nuts. The reinforcement brackets
should rest tightly against the rail lower flanges.
3.
Position the receiver on the vehicle with the rear attachment holes aligned with the holes in the reinforcement brackets. Loosely install the
9/16 X 1.50hex bolts and 9/16" locknuts in the rear holes as shown. (Note: Locknuts should be inside the frame rails).
Center the receiver on the frame. Using the receiver as a template, drill four (4) 9/16" holes into the frame.
4.
5.
Install the remaining fasteners as shown, placing the blocks inside the frame rails.
6.
If the under-box storage is to be retained, modify and/or relocate the spare tire carrier.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006, 2012 Cequent Performance Products
Installation Instructions
Dodge Pickup Full Size – All W/8' Box
Frame
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all 9/16 GR5 fasteners with torque wrench to 120 Lb.-Ft. (163 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3, PU4
Frame
L.H./R.H
Bracket
(4375-001, 4375-002)
n
Qty. (4)
1/2-13 X 1.25 GR5 Hex Bolt
o
Qty. (4)
Lock Washer
p
Qty. (4)
1/2-13 Hex Nut
Sheet 1 of 3
N41902
Part Numbers:
41902
96902
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
12,000
1200
10,000
1000
6-1-12
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 41902
Resumen de contenidos para Cequent Performance Products 41902
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2006, 2012 Cequent Performance Products Sheet 1 of 3 N41902 6-1-12 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2006, 2012 Cequent Performance Products Feuille 2 de 3 N41902 6-1-12 Rev.
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2006, 2012 Cequent Performance Products Hoja 3 de 3 N41902 6-1-12 Rev.