Milwaukee REDLITHIUM 3510-20 Manual Del Operador página 6

A
d
8. The distance between points I and III on wall A is
the height deviation (d) of the tool. This distance
should not exceed 1/8" (max.) at 33' (1/2" at 132').
For the Measuring distance of 2 x 66' = 132', the maxi-
mum allowable deviation (d) is: 132' x ±1/8" ÷ 33' = ±1/2".
Vertical Leveling Accuracy
A free measuring distance of approximately 16.5'
between floor and ceiling on a firm surface is required
for this check.
1. Draw a straight line on the ceiling to use as a
reference line.
2. Securely mount the tool within 1' of the floor.
3. Turn the tool to
4. Position the tool so that the bottom plumb point
can be seen on the floor and the center of the top
plumb point is located on the reference line on the
ceiling. Allow the tool to self-level.
5. Mark the center of the top plumb point with the refer-
ence line on the ceiling (point I). Also, mark the cen-
ter of the bottom plumb point on the floor (point II).
6. Rotate the tool 180°. Align the center point of the
laser beam directly onto the floor point II.
7. Position the tool to align the center of the top plumb
point onto the reference line on the ceiling. It may
be necessary to rotate the tool slightly to align.
Allow the tool to self-level.
8. Mark the center of the top plumb point on the
reference line on the ceiling (point III).
180
ON.
16.5'
d
9. The distance between points I and III on the ceiling
is the deviation (d) of the tool. This distance should
not exceed 1/8" (max.) at 33'.
B
For the Measuring distance of 2 x 16.5' = 33', the
maximum allowable deviation (d) is: 33' x ±1/8"
÷ 33' = ±1/8".
MAINTENANCE
WARNING
ing any maintenance. Never disassemble the tool.
Maintain tools. If damaged, have the tool repaired
before use. Accidents may be caused by poorly
maintained tools.
WARNING
your tool in liquid or allow a liquid to flow inside
them.
Keep tool handles clean, dry and free of oil or grease.
Use only mild soap and a damp cloth to clean the tool
since certain cleaning agents and solvents are harm-
ful to plastics and other insulated parts. Some of these
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never
use flammable or combustible solvents around tools.
Blow off loose particles with clean compressed air.
Carefully wipe the surface with a cotton swab moist-
ened with water.
This tool has limited serviceable parts. Do not open
housing or disassemble tool. For repairs, return the
tool, battery pack and charger to the nearest autho-
rized service center.
ACCESSORIES
WARNING
any other accessories may create risk of injury.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit
Contact Corporate After Sales Service Technical Support
with technical, service/repair, or warranty questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
Milwaukee Tool (Canada) Ltd
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted to the
original purchaser only to be free from defects in material and workman-
ship. Subject to certain exceptions, MILWAUKEE will repair or replace any
part on an electric power tool which, after examination, is determined by
MILWAUKEE to be defective in material or workmanship for a period of
five (5) years** after the date of purchase unless otherwise noted. Return
6
To reduce the risk of injury, always
remove the battery before perform-
Maintain Laser Level
To reduce the risk of personal in-
jury and damage, never immerse
Cleaning
Cleaning the Lenses
Repairs
Use tools only with specifically
designated accessories. Use of
www.milwaukeetool.com
SERVICE - CANADA
1.800.268.4015
(1.800.729.3878)