smith&nephew T-MAX Modo De Empleo página 5

4. Once patient is anesthetized, remove arms from inside Lateral
Supports. Anesthetist will control head as patient is raised to
sitting position.
5. Intubation pad is removed and replaced with Surgical Headset
which is adjusted to attain ideal head positioning by adjusting
height (Vertical Adjustment Knob,) head angle (Ball and Socket
Knob,) and forward translation (Headset Forward Slide Knob.) To
remove Intubation Pad the anesthetist must control the patient's
head. Loosen Double Ball and Socket and tilt pad back as far as
possible. Loosen Forward Slide Knob and remove Intubation Pad,
replace with Surgical Headset, adjust position and tighten headset.
Once positioning is complete, patient's head is secured in place
using the Face Mask. The Face Mask provides pressure to the
forehead and chin to secure the head in place during surgery. This
head positioning ensures the head and airways will be in a neutral
position throughout the surgical case. Face mask attaches into
two clips on each side of the Surgical Headset. Position mask and
tighten mask by pulling straps.
If using Surgical Headset:
1. Lower Surgical Headset so pad is behind patient's neck. Loosen
Forward Slide Knob and slide Surgical Headset as far back as
possible. Lower patient to supine and the head will slide down
headset to the center of the pad.
2. Ball and Socket can be loosened to allow the anesthetist to
manipulate Surgical Headset for optimal positioning. Anesthetist is
also free to use any usual techniques for intubation including use of
pillows under head and shoulders.
3. Once anesthetized, control patient's head while raising to a sitting
position. Place Face Mask on patient and tighten straps. Adjust
head position as required.
4. Once positioned the patient can be draped. When an anesthetic
block is used the Drape Bar attaches to the Surgical Headset and
keeps the drape off the patient's face.
5. Positioning is not generally adjusted during the surgery, but can be
adjusted under the drape if necessary. Extra care must be taken to
ensure pressure is not created on patient's head or neck structures
during adjustments.
6. Following the procedure, remove draping.
7. Release Face Mask and lower headset pad behind patient's neck.
8. Use Lift System Release Handle to slowly lower patient to supine
position.
9. Remove Lateral Support from transfer side before moving patient
from the Beach Chair to a stretcher.
10. Smith & Nephew's SPIDER Limb Positioner can be used to intra-
operatively position the operative arm during surgery. When using
the T-MAX, the SPIDER is attached to the Attachment Bar on the
back of the T-MAX Beach Chair.
For additional information please see SPIDER Limb Positioner and
Beach Chair Shoulder Bar Instructions for Use.
T-MAX Beach Chair Instructions for Use
Cleaning
• Wipe pads with mild detergent/disinfectant following each case.
• Avoid moisture contact on Hex Shaft of T-MAX.
• Dry off Hex Shaft after use.
• Disposable foam masks should be discarded after each surgery.
Storage
The T-MAX is stored on its own cart for transportation and storage.
To place T-MAX on cart, move Headset forward. Lift T-MAX by the Lift
System Release Handle and place Lift System Release Handle over
front hook on cart. Bottom of cylinders rest against cylinder rests.
Intubation pad goes between slide pad and knee bolster. Arm board
post sits on side storage hook on cart. Clamp post at bottom of cart
holds both Square Rail Clamps. Knee Bolster is wedged between
Lateral Supports and tightened in place.
Warranty
This product has a standard 12-month parts and labor warranty against
manufacturing defects.
For Further Information
If further information on this product is needed, contact Smith &
Nephew Customer Service at +1 800 343 5717 in the U.S., or an
authorized representative.
©2014 Smith & Nephew, Inc.
All rights reserved.
English
29-99-01 Rev. C
5