Andis Sensa-Charge AGR+ Manual Del Usuario página 6

REMOVING BLADE SET
To remove blade set, first make sure your clipper motor is switched "OFF". Push blade release
mechanism under blade hinge (Figure E). While holding down the blade release mechanism, push down
on blade, then gently pull the blade forward (Figure F), and slide it off the blade hinge. If your blade
hinge should snap closed and is flush with the clipper, use a small standard screwdriver to pry the tongue
of the hinge out (Figure G). NOTE: Hair may accumulate in the front cavity of the housing under the
blade. If this happens, you can clean out the hair by brushing out the cavity with a small brush or an old
toothbrush while the blade is off the clipper.
REPLACING OR CHANGING BLADE SET
To replace or change your blade set, slide the blade bracket onto the hinge of the clipper (Figure H), and
with the clipper turned "ON", push the blade towards the clipper to lock into position.
BLADE TEMPERATURE
Due to the high speed nature of Andis clippers, please check for blade heat often, especially on close-
cutting blades. If blades are too hot, dip the blades only into Andis Blade Care Plus or apply Andis Cool
Care Plus and then Andis Clipper Oil. If you have a detachable blade unit, you can change your blade in
order to maintain a comfortable temperature; using multiple blades of the same size is popular among
groomers.
CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES
Blades should be oiled before, during, and after each use. If your clipper blades leave streaks or slow
down, it's a sure sign blades need oil. Place a few drops of oil on the front and side of the cutter blades
(Figure I). Wipe excess oil off blades with a soft, dry cloth. Spray lubricants contain insufficient oil for
good lubrication, but are an excellent clipper blade coolant. Always replace broken or nicked blades to
prevent injury. You can clean the excess hair from your blades by using a small brush or worn out
toothbrush. To clean the blades, we suggest to immerse the blades only into a shallow pan of Andis
Clipper Oil, while the clipper is running. Any excess hair and dirt that has accumulated between the
blades should come out. After cleaning, turn your clipper off and dry blades with a clean dry cloth and
start clipping again. If upon cleaning your blades you find that the blades will still not cut, there may be
a few fine pieces of hair trapped between the upper and lower blade. If this happens, you will need to
snap the blade off the clipper. Proceed to slide the upper blade to one side, without loosening the
tension spring or moving the upper blade completely out from under the tension spring (See Figure J for
position of blade). Wipe the surface between the blades clean with a dry cloth, then place a drop of
clipper oil where the upper and lower blades meet and also in the guide slot of the tension spring
(Figure J). Now slide the upper blade to the opposite side of the lower blade and repeat this process.
After completing this procedure, slide the upper blade, centering it over the lower blade. Handle or
store your Andis clipper with the blades down so excess oil will not run into the clipper case.
CHANGING THE BLADE DRIVE ASSEMBLY
If your clipper blades no longer cut properly (be sure to try more than one blade, since the blade
currently being used may be dull), it could be that your blade drive assembly needs replacement.
TO CHANGE THE BLADE DRIVE ASSEMBLY:
1. Remove blade set (Figure F).
2. Remove drive cap (Figure K).
3. Remove blade drive mounting screws (Figure L).
4. NOTE: Before removing blade drive assembly, note the way it is positioned (this will help you in
reassembly). Remove blade drive assembly (Figure M).
5. Drive bearing should be at its lowest position, if not, move it with your finger to lowest position
(Figures N & O).
6. Put on new drive assembly, align screw holes and press down (Figure M).
7. Reassemble blade drive by replacing mounting screws, turning just until snug (Figure L). DO NOT
OVERTIGHTEN.
8. Replace drive cap (Figure K).
9. Replace blade (Figure H).
BLADE & CLIPPER/TRIMMER REPAIR SERVICE
When the blades of your Andis clipper/trimmer become dull after repeated use, it is advised to purchase
a new set of blades available through your Andis supplier. Some blade sets can be resharpened – contact
your Andis supplier or the Andis Company for information on resharpening. If you wish your clipper/
trimmer to be serviced as well, contact your Andis supplier. If you have a problem contacting your Andis
supplier, contact the Andis Company customer service department 1-262-884-2600 (USA) or email at
info@andisco.com. To find an Andis Authorized Service Station near you log on to www.andis.com
or contact our customer service department by phone at 1-262-884-2600 (USA), or by email at
info@andisco.com.
6